|
[Sponsors] |
How to make simulation of body force in plasma actuator induce flow? |
![]() |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
![]() |
![]() |
#21 |
Senior Member
Mominul MuKuT
Join Date: Mar 2009
Location: Bangladesh
Posts: 124
Rep Power: 16 ![]() |
Dear Richard,
Thank you. I am waiting for your reply. I have sent you the q1 file, please check PVT msg. mukut |
|
![]() |
![]() |
![]() |
![]() |
#22 |
Senior Member
Mominul MuKuT
Join Date: Mar 2009
Location: Bangladesh
Posts: 124
Rep Power: 16 ![]() |
Dear Richard,
have you got Q1 file? There are some error and today's I have made correction. like at North wall the value of EPOT should be XG^2-0.01 I have used two inlet BC but one is ok, I think....because I initialize permittivity in air and dielectric separately.... I don't understand how to apply Prndlt(EPOT).... another thing is there are some technical fault in Phoenics in our campus, computer center confirmed some error in PLANT coding.....so I can't use any PLANT code in Q1. Now EPOT looks like as follows: ![]() Thickness of electrode is too small so how can I define such micro scale thickness? or defining the electrode at the south and north wall for upper and lower domain respectively? I am waiting for your next reply.... Today I have tried several times to open this forum and sometime it opens but during submitting reply, then page load error is occurred ![]() |
|
![]() |
![]() |
![]() |
![]() |
#23 |
Senior Member
Mominul MuKuT
Join Date: Mar 2009
Location: Bangladesh
Posts: 124
Rep Power: 16 ![]() |
Dear Richard,
Where are you? please help me ![]() |
|
![]() |
![]() |
![]() |
![]() |
#24 |
Senior Member
Mominul MuKuT
Join Date: Mar 2009
Location: Bangladesh
Posts: 124
Rep Power: 16 ![]() |
anybody help me please...
|
|
![]() |
![]() |
![]() |
![]() |
#25 |
Senior Member
Mominul MuKuT
Join Date: Mar 2009
Location: Bangladesh
Posts: 124
Rep Power: 16 ![]() |
I am still crawling.......need some help to go smoothly. Please if you have any suggestion please write here.
Thnx |
|
![]() |
![]() |
![]() |
![]() |
#26 |
New Member
designer spider
Join Date: Sep 2010
Posts: 7
Rep Power: 14 ![]() |
Please check my thread also.
Last edited by black_spider; April 7, 2011 at 22:53. |
|
![]() |
![]() |
![]() |
Tags |
body force, phoenics, plasma actuator, simulation |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help with slug flow simulation. | Kes | FLUENT | 3 | November 9, 2019 21:39 |
Installation OF1.5-dev | ttdtud | OpenFOAM Installation | 46 | May 5, 2009 02:32 |
The lift force coefficient in bubbly flow | Kai Yan | Main CFD Forum | 1 | November 4, 2008 13:54 |
Regarding FoamX running Kindly help out | hariya03 | OpenFOAM Pre-Processing | 0 | April 18, 2008 04:26 |
OpenFOAM with IBM AIX | matthias | OpenFOAM Installation | 20 | March 25, 2008 02:36 |