|
[Sponsors] |
|
September 11, 2023, 03:23 |
About parameter settings
|
#1 |
New Member
GeZi
Join Date: Jul 2023
Posts: 23
Rep Power: 2 |
Dear REEF3D Team,
Thank you for your amazing software!However, I have doubts about the following options when using the software: F 10 2 //Does it necessary to open it when simulating bridge pier scour and select two phases? F 39 0.5 //What is the function of this option? F 43 0.55 //What is the function of this option?Does it only need to select one between F43 and F44? F 44 3 //What is the difference between this option and the later S37? Does it represent the reinitialization time step of the water-air interface, while S37 represents the reinitialization time step of the water-sand interface? F 49 1 //Does it necessary to open it when simulating bridge pier scour? I 10 1 //In bridge scour simulation, does it necessary to simultaneously activate I11, I12, and I13 after activating this option? N 47 0.1 //The following S14 option also represents the time step relaxation factor. Should one of N47 and S14 be taken when simulating bridge scour, or should both be turned on and the values be the same? S 43 50000 //What is the appropriate value to take? S 44 200 //When viewing scour depth data, extract the results based on "simtime", and the S44 option will affect "simtime". What is the appropriate value for this option? T 35、T 36、T 37、T 38 //Do these options need to be manually enabled or will they be enabled by default when starting the k-w turbulence model? Looking forward to suggestions. Thanks GeZi |
|
September 11, 2023, 04:21 |
|
#2 |
New Member
GeZi
Join Date: Jul 2023
Posts: 23
Rep Power: 2 |
In addition, I would like to know from which literature can the VOF theory used in REEF3D be obtained?
|
|
September 11, 2023, 05:39 |
|
#3 |
Super Moderator
Hans Bihs
Join Date: Jun 2009
Location: Trondheim, Norway
Posts: 386
Rep Power: 18 |
Regarding the free surface, I would stick to the standard (i.e. level set function). It seems that you are trying to work with a couple of complex algorithms (sediment + 6DOF). So for the rest, best to keep things simple.
F 10 2 -> don't change F 39 0.5 -> not needed F 43 0.55 -> don't change F 44 3 -> don't change, no connection to S37 I 10 1 -> depends on your flow condition N 47 0.1 -> S14 and N47 are not connected S 43 50000 -> depends on, but your number is too high. you could try something between 100 and 1000 S 44 200 -> 10 T 35、T 36、T 37、T 38 -> don't change |
|
September 11, 2023, 05:53 |
|
#4 | |
New Member
GeZi
Join Date: Jul 2023
Posts: 23
Rep Power: 2 |
Quote:
|
||
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Incomplete writing to .csv files during parameter sweeps | SiemenDiemon | STAR-CCM+ | 2 | September 17, 2020 03:40 |
customized BCs: using value as gradient of another parameter and no constraint | shuxuejia | OpenFOAM Programming & Development | 1 | August 21, 2020 23:38 |
temperature as output parameter | lukas' | FLUENT | 0 | June 15, 2020 08:47 |
Question on running CFX simulations in workbench parameter set table | Anna Tian | CFX | 0 | September 20, 2014 01:51 |
compile errors of boundary condition "expDirectionMixed" | liying02ts | OpenFOAM Bugs | 2 | February 1, 2010 20:11 |