Forum: ANSYS Meshing & Geometry
August 16, 2017, 04:37
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 16, 2017, 03:46
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 16, 2017, 03:08
|
Replies: 38
Views: 2,801
Hello dear Maxime,
1- I have exported the mesh...
Hello dear Maxime,
1- I have exported the mesh without axis boundary to openfoam then I run createPatch command to change the FRONT and BACK boundary type to cyclic after this some .obj files were...
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 08:56
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 08:50
|
Replies: 38
Views: 2,801
Ok, thanks I'll do that.
I have another...
Ok, thanks I'll do that.
I have another question
I want to use cyclic boundary condition in OF for front and back faces but as I see there isn't such a boundary condition in Gambit!
what should I...
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 08:26
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 08:12
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 07:58
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 07:50
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 07:33
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 07:18
|
Replies: 38
Views: 2,801
I'm not sure but I think I have seen it...
I'm not sure but I think I have seen it somewhere!
but if you're sure that there isn't necessity for axis boundary in 3d cases then I will do that.
Dear Maxime, may you have a look at my gambit...
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 07:07
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 14, 2017, 06:53
|
Replies: 38
Views: 2,801
I tried to delete the edge but it said: It can...
I tried to delete the edge but it said: It can not be deleted because it is being referenced by upper topology entity!
As you can see in the photos the AXIS edge is being referenced by the two front...
|
Forum: ANSYS Meshing & Geometry
August 13, 2017, 04:01
|
Replies: 38
Views: 2,801
57722
57723Hello Maxime,
I have created a...
57722
57723Hello Maxime,
I have created a sector of a cylinder and meshed it.
Now, when I am defining boundary conditions it says there are errors especially when I export the mesh for fluent it...
|
Forum: ANSYS Meshing & Geometry
August 8, 2017, 13:26
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 8, 2017, 06:27
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 8, 2017, 05:25
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 8, 2017, 05:11
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 8, 2017, 05:09
|
Replies: 38
Views: 2,801
|
Forum: ANSYS Meshing & Geometry
August 8, 2017, 04:55
|
Replies: 38
Views: 2,801
Thanks for your reply.
But I don't want to...
Thanks for your reply.
But I don't want to create a full cylinder geometry, I want to create a 30 degree sector of a cylinder and my problem is with its' corner mesh. Actually, I don't know what is...
|
Forum: ANSYS Meshing & Geometry
August 7, 2017, 15:31
|
Replies: 38
Views: 2,801
Sector of a Cylinder
Hello everybody,
Can any one tell me how to draw and mesh a 30 degree sector of a cylinder in gambit, that has the best meshing quality for CFD simulations?
Thanks in advance
|