Search Results

User Name Remember Me Password

Showing results 1 to 9 of 9 Search took 0.00 seconds. Search: Posts Made By: ViLaks

Forum: FLUENT February 23, 2020, 23:53

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Hi Bran, I used ANSYS Fluent for... Hi Bran, I used ANSYS Fluent for simulations. To specify initial conditions, I just initialised the problem at 43 °C. I did not proceed with implementing fan for various reasons. I just used a...

Forum: FLUENT November 27, 2017, 23:34

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Yes!!! Thanks !!! But I was able to simulate... Yes!!! Thanks !!! But I was able to simulate fan and natural convection together !!! There was considerable increase in heat transfer !!! Regards Vignesh

Forum: FLUENT November 23, 2017, 23:39

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Dear Foxhunter, I have planned to run the... Dear Foxhunter, I have planned to run the fan seperately and compute the air flow rate, which then can be given as velocity input, such that the fan sucks from and delivers within the deep...

Forum: FLUENT November 23, 2017, 00:10

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Hi All, I have managed to finally simulate... Hi All, I have managed to finally simulate the problem . Next part is how to solve the problem. Using natural convection, the time taken for pull down is too long (1.5 hrs). In order to enhance...

Forum: FLUENT November 6, 2017, 04:30

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Hmm. Thanks for your reply Hmm. Thanks for your reply

Forum: FLUENT November 6, 2017, 04:18

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Dear Foxhunter, In case I neglect it,... Dear Foxhunter, In case I neglect it, already the wall will be having non uniform temperature distribution, wouldnt it be too much approximation? This might increase the error in my results right

Forum: FLUENT November 6, 2017, 04:16

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Dear Lucky Tran, What I meant was, what HTC... Dear Lucky Tran, What I meant was, what HTC to use? That of the steady state or transient run? In both the cases, the HTC at the end of simulation (ie, when the transient run has reached steady...

Forum: FLUENT October 31, 2017, 04:34

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Dear Lucky Tran, Thanks for your reply. ... Dear Lucky Tran, Thanks for your reply. How am I supposed to do this? My freezer volume is 500 Litres hard top with PUF thickness of 60 mm As you said, I am getting this exponential...

Forum: FLUENT October 27, 2017, 01:31

Replies: 15 Temperature Pull Down Simulation using Fluent Views: 2,007 Posted By ViLaks Temperature Pull Down Simulation using Fluent Hello All, I am working on estimating the time taken for temperature pull down inside a deep freezer using Fluent. The deep freezer, which is functional, is switched off. The Lid is opened...

Showing results 1 to 9 of 9

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki