Search Results

User Name Remember Me Password

Showing results 1 to 8 of 8 Search took 0.02 seconds. Search: Posts Made By: luxingzhe

Forum: ANSYS Meshing & Geometry February 25, 2012, 11:15

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe I suppose the strategy you used was this: block... I suppose the strategy you used was this: block your domain, set the mesh parameters, pre-mesh, convert pre-mesh into unstructured mesh, then before you write fluent mesh file, go to mesh edit, where...

Forum: ANSYS Meshing & Geometry February 24, 2012, 12:32

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe Not sure about your problem. did you mesh the... Not sure about your problem. did you mesh the model in ICEM, if you did, take very care attention to the periodicity (my problem regarding importing mesh into Fluent was due to periodicity), if you...

Forum: ANSYS Meshing & Geometry December 28, 2011, 12:41

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe Just to let you know that the problem is solved,... Just to let you know that the problem is solved, i am now playing with Fluent, but it shows there are some elements with poor quality, which i hope doesn't influence the results too much. Now i...

Forum: ANSYS Meshing & Geometry December 26, 2011, 18:41

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe hi, simon. i have to send you another message... hi, simon. i have to send you another message about the periodicy. I followed the right procedures seting up the periodicy in ICEM, and the mesh check shows no problems. but why doesn't Fluent allow...

Forum: ANSYS Meshing & Geometry December 21, 2011, 06:22

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe hi Simon i tried again, i think the problem... hi Simon i tried again, i think the problem must be the mesh, i got a few bad elements around the blade tip, which made the whole mesh unreadable. However, do you have better ways to block it? it...

Forum: ANSYS Meshing & Geometry December 20, 2011, 16:58

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe Thanks for the reply, really appreciate that. ... Thanks for the reply, really appreciate that. first of all, what do you mean by same model, two blocks. is it like you build a block around the blade and then build a bigger block for the inner...

Forum: ANSYS Meshing & Geometry December 16, 2011, 05:31

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe Simon, it would be great if you can have a look... Simon, it would be great if you can have a look at my problem.

Forum: ANSYS Meshing & Geometry December 16, 2011, 05:24

Replies: 16 [ICEM] 3D Wind turbine mesh Views: 5,709 Posted By luxingzhe 3D Wind turbine mesh Dear All I am planning to use sliding mesh model to simulate my wind tubine. i build the geometry in gambit, exported step file, and imported into ICEM for mesh. you can see from the step file...

Showing results 1 to 8 of 8

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki