Search Results

User Name Remember Me Password

Showing results 1 to 12 of 12 Search took 0.00 seconds. Search: Posts Made By: Clecl

Forum: ANSYS Meshing & Geometry September 24, 2012, 04:04

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Thank you very much! It reassures me! I have... Thank you very much! It reassures me! I have indeed single edges all around my perimeter, and only there. Thanks a lot!

Forum: ANSYS Meshing & Geometry September 21, 2012, 08:38

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Thank you for your reply. I finally found my... Thank you for your reply. I finally found my mistake a week ago: my axis was not the X-axis, so it didn't work on Fluent with the Axissymmetric model (because the axis of symetry have to be the...

Forum: ANSYS Meshing & Geometry September 6, 2012, 10:59

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl There is no error when I check the mesh if I... There is no error when I check the mesh if I choose 2D planar in general model in Fluent. If I choose Axisymetric or Axisymetric Swirl, check mesh failed! Thank you for your help, maybe I can run...

Forum: ANSYS Meshing & Geometry September 6, 2012, 09:57

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Thank you. I tried this with my current geometry... Thank you. I tried this with my current geometry but it failed (when I check the mesh in fluent, "check mesh failed"). But I am starting a new project (I restart from the beginning to avoid...

Forum: ANSYS Meshing & Geometry September 6, 2012, 08:34

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl I forgot the corresponding geometry I forgot the corresponding geometry

Forum: ANSYS Meshing & Geometry September 6, 2012, 08:30

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Here it is! I fail and fail, and I don't... Here it is! I fail and fail, and I don't understand why :confused:... Don't hesitate if you have any idea to get me out of there!! Thank you (again :))

Forum: ANSYS Meshing & Geometry September 6, 2012, 03:24

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Yes it is! But even with an easier geometry I... Yes it is! But even with an easier geometry I have the problem of the single edges (I tried with a square yesterday...). I don't understand where I'm wrong... I join the tin file. I tried the...

Forum: ANSYS Meshing & Geometry September 5, 2012, 09:00

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Do you mean that I have to a build diagnostic... Do you mean that I have to a build diagnostic topology (in "Repair Geometry")? (I tried this, but I don't know which option I had to choose)

Forum: ANSYS Meshing & Geometry September 5, 2012, 07:26

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Thank you, I'm going to try this, I'll tell you... Thank you, I'm going to try this, I'll tell you later if it is the solution!

Forum: ANSYS Meshing & Geometry September 5, 2012, 04:28

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl * it changes nothing for single edge when I... * it changes nothing for single edge when I refine the mesh

Forum: ANSYS Meshing & Geometry September 5, 2012, 04:27

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl geometry Thank you for your reply. I join geometry. Here my mesh is coarse, but it isn't the problem and it changes for single edgesnothing when I refine. (INLET_TERTIAIRE = there are 2 inlets of tertiary...

Forum: ANSYS Meshing & Geometry September 4, 2012, 09:49

Replies: 21 [ICEM] Checking the mesh -> problem of single edges Views: 6,749 Posted By Clecl Checking the mesh -> problem of single edges Hi! (I apologize for the mistakes) I'm a beginner regarding ICEM-CFD. I have to mesh a simple 2D axisymetric geometry. My mesh quality is very good (>0.8). But when I check the mesh, it...

Showing results 1 to 12 of 12

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki