Forum: CFX
November 5, 2018, 15:12
|
Replies: 49
Views: 2,975
|
Forum: CFX
November 2, 2018, 06:27
|
Replies: 49
Views: 2,975
|
Forum: CFX
November 2, 2018, 06:21
|
Replies: 49
Views: 2,975
I had this example in mind, showing the use of...
I had this example in mind, showing the use of multiple coordinate systems in 1 simulation. It shows the movement of rotating immersed solids in a rotating domain. There is no flow. I hope it helps.
|
Forum: CFX
November 2, 2018, 03:28
|
Replies: 49
Views: 2,975
That is why I advised to create a very simple...
That is why I advised to create a very simple geometry and calculate the movements of all objects without calculating the flow. To first find out how everything behaves and moves like you want. Start...
|
Forum: CFX
November 2, 2018, 03:26
|
Replies: 49
Views: 2,975
|
Forum: CFX
October 31, 2018, 15:47
|
Replies: 49
Views: 2,975
I don't understand this. If I am correct, CFX...
I don't understand this. If I am correct, CFX creates the Global Axis on the origin (0,0,0). As a check, you can always create a monitoring point with certain coordinates to find where you are in the...
|
Forum: CFX
October 31, 2018, 15:41
|
Replies: 49
Views: 2,975
|
Forum: CFX
October 31, 2018, 03:40
|
Replies: 49
Views: 2,975
|
Forum: CFX
October 26, 2018, 08:33
|
Replies: 49
Views: 2,975
Yes. No problem
No, not necessary....
Yes. No problem
No, not necessary. Certainly, if you have a coarse mesh on either side, it will affect your solution. Therefore, you could perform some tests to check their influence.
|
Forum: CFX
October 26, 2018, 07:28
|
Replies: 49
Views: 2,975
As I already mentioned, you can close the gap....
As I already mentioned, you can close the gap. Then there will be a wall with zero thickness. Do not include this wall in any way in your CFD-calculation. It should be completely absent.
Then,...
|
Forum: CFX
October 26, 2018, 06:12
|
Replies: 49
Views: 2,975
Your separating wall and pressure and suction...
Your separating wall and pressure and suction chambers are fixed, in the stationary frame. The separating wall will be (almost) perpendicular to your interface. So, it won't be part of the interface....
|
Forum: CFX
October 24, 2018, 11:09
|
Replies: 49
Views: 2,975
|
Forum: CFX
October 24, 2018, 09:33
|
Replies: 49
Views: 2,975
Put the interface on the circular outerwall of...
Put the interface on the circular outerwall of the pressure/suction chamber and gap. Over 360°. As a result, on the inner sideof the interface there will be fluid everywhere. On the outside of the...
|
Forum: CFX
October 24, 2018, 09:13
|
Replies: 49
Views: 2,975
|
Forum: CFX
October 24, 2018, 08:09
|
Replies: 49
Views: 2,975
Yes you need an interface. I think the right...
Yes you need an interface. I think the right location will be as indicated by the green circle, see my attachement.
(I thought you wanted an interface around your pistons. But neither with moving...
|
Forum: CFX
October 24, 2018, 04:43
|
Replies: 49
Views: 2,975
|
Forum: CFX
October 24, 2018, 04:31
|
Replies: 49
Views: 2,975
With moving/deforming mesh, I would suggest to...
With moving/deforming mesh, I would suggest to leave out the gap. And there won't be an interface.
The top wall will move in and out, depending on its angular position. The side walls will adapt....
|
Forum: CFX
October 23, 2018, 13:08
|
Replies: 49
Views: 2,975
|