Forum: OpenFOAM Running, Solving & CFD
November 21, 2015, 07:17
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 20, 2015, 07:15
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 20, 2015, 05:57
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 20, 2015, 04:58
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 20, 2015, 04:05
|
Replies: 45
Views: 3,348
Hi, i think that your mesh is good.
As i...
Hi, i think that your mesh is good.
As i undestrand, you are using transient solver (pimpleFoam?)
Try next:
1) Set momentumPredictor in fvSolution->PIMPLE to false
2) Set nCorrectors to 2...
|
Forum: OpenFOAM Running, Solving & CFD
November 13, 2015, 04:20
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 11, 2015, 04:17
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 11, 2015, 03:49
|
Replies: 45
Views: 3,348
Because you introduced new block, that is not...
Because you introduced new block, that is not connected to others. You must split this block to connect to point 4, 59, 60, 61, 62, 1. See attached jpg for example, new points are marked with red...
|
Forum: OpenFOAM Running, Solving & CFD
November 9, 2015, 09:46
|
Replies: 45
Views: 3,348
Hi, i checked your blockMeshDict and i can...
Hi, i checked your blockMeshDict and i can propose next changes
1) If you want to comment something between '(' and ')' brackets, use two slashes, for example:
// inlet
// {
// ...
|
Forum: OpenFOAM Running, Solving & CFD
November 7, 2015, 06:40
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 7, 2015, 06:03
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 2, 2015, 05:05
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 2, 2015, 04:59
|
Replies: 45
Views: 3,348
Yes, you can, but if you will do lower part of...
Yes, you can, but if you will do lower part of mesh like in example tutorials/stressAnalysis/solidDisplacementFoam/plateHole
or like the top part, you will get better mesh quality, i think.
Also,...
|
Forum: OpenFOAM Running, Solving & CFD
November 2, 2015, 04:37
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
November 2, 2015, 03:59
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
October 31, 2015, 05:52
|
Replies: 45
Views: 3,348
|
Forum: OpenFOAM Running, Solving & CFD
October 30, 2015, 08:58
|
Replies: 45
Views: 3,348
Yes
You must locate cells where...
Yes
You must locate cells where non-orthogonality is high and change geometry of corresponding blocks in blockMeshDict. To locate this cells, run:
checkMest
then
|
Forum: OpenFOAM Running, Solving & CFD
October 30, 2015, 04:31
|
Replies: 45
Views: 3,348
|