|
[Sponsors] |
Erro while running moving mesh in linux version. |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
November 13, 2004, 01:32 |
Erro while running moving mesh in linux version.
|
#1 |
Guest
Posts: n/a
|
Hello everyone!
When I using starCD3.15 in linux version to running moving mesh case of tutorial 7.1,it can not run correctly,and there are erros as License info: CDLMD_LICENSE_FILE=/opt/starcd/license/license.dat (from ~/.flexlmrc) Checking out starsolver *** GEOMETRICAL CALCULATIONS STARTED *** GEOMETRICAL CALCULATIONS COMPLETED Could not find and execute PROSTAR Can anyone tell me what's the problem,and what I should do to running correctly? Thanks a lot! xhliu1 |
|
November 13, 2004, 02:03 |
Re: Erro while running moving mesh in linux versio
|
#2 |
Guest
Posts: n/a
|
You must run pmovlink first - that creates the script PROSTAR.
|
|
November 13, 2004, 02:57 |
Re: Erro while running moving mesh in linux versio
|
#3 |
Guest
Posts: n/a
|
Thank you very much,Brian!
I am sure that I have typed starlink pmovlink and star after I running star,I have saw the information I have posted above! xhliu1 |
|
November 13, 2004, 06:37 |
Re: Erro while running moving mesh in linux versio
|
#4 |
Guest
Posts: n/a
|
wrong !!
1) pmovlink 2) starlink 3) star |
|
November 13, 2004, 08:17 |
Re: Erro while running moving mesh in linux versio
|
#5 |
Guest
Posts: n/a
|
But I have tried this turn of these words,but it does not work yet.
|
|
November 13, 2004, 08:59 |
Re: Erro while running moving mesh in linux versio
|
#6 |
Guest
Posts: n/a
|
What does it mean, the it does not work? What are the error messages or the output from each of the steps?
Just try it again: 1) load the model in prostar 2) connect the event file by using the command "evfi ,," 3) connect the transient file "trfi ,, " 3a) if you have more than 1 load step defined do a "lsra 1 , XX" where XX is the max defined loadstep 4) write the geometry file "geom ,," 5 ) write the problem file "prob ,," 6) close prostar 7) run pmovlink 8) run starlink 9) run star Look at the output from any of these steps. |
|
November 14, 2004, 10:48 |
Re: Erro while running moving mesh in linux versio
|
#7 |
Guest
Posts: n/a
|
Check if "." is in the path - it should be (echo $PATH)
|
|
November 15, 2004, 04:40 |
Re: Erro while running moving mesh in linux versio
|
#8 |
Guest
Posts: n/a
|
How can I start the basics of the star CD program? From where?
|
|
November 15, 2004, 10:25 |
Re: Erro while running moving mesh in linux versio
|
#9 |
Guest
Posts: n/a
|
IF you use starcd of windows version you should double-press "starcd batch",set you working directry and press "prostar"on the batch. if you use starcd of linux or unix version you should enter your working directry and type "prostar",do as this, I think you can do what you want.
|
|
November 15, 2004, 10:36 |
Re: Erro while running moving mesh in linux versio
|
#10 |
Guest
Posts: n/a
|
My set file is
# .cshrc $ user specific aliases and functions alias rm 'rm -i' alias cp 'cp -i' alias mv 'mv -i' setenv PATH "/usr/local/sbin:/urs/sbin:/sbin:${PATH}:${HOME}/bin" setenv STARDIR /opt/v3150 set path = ( /opt/v3150/bin $path) set path = ( . $path ) set CDLMD_LICENSE_FILE=opt/v3150/license/license.dat set prompt=\['id -nu'@'hostname -s'\]\#\ can you give me some advice? Thank you very much! |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Moving Mesh Run problem - Scientific Linux | G. SE | Siemens | 2 | May 7, 2008 08:15 |
Running Fluent on Red Hat Linux WS version 4 | Bob | FLUENT | 1 | September 4, 2005 06:01 |
Help?Running erro? | robert | Siemens | 1 | January 21, 2005 11:43 |
Help???Subroutine running erro? | blackhole | Siemens | 5 | December 17, 2004 08:12 |
Can not using moving mesh in starCD of linux | xhliu1 | Siemens | 4 | October 17, 2004 10:12 |