Threads Tagged with cyclic boundaries

Threads Tagged with cyclic boundaries
	Thread / Thread Starter	Last Post	Replies	Views	Forum
	Cyclic AMI patch minimum weight goes to zero muhammss	October 7, 2022 05:26 by Tobi	16	4,847	OpenFOAM Running, Solving & CFD
	matching error in cyclic patches in spite of having same number of faces atul1018	August 12, 2022 08:47 by Gavin Tall	3	565	OpenFOAM Pre-Processing
	Appropriate boundary type for reactor fuel simulation fuad	August 2, 2022 13:17 by fuad	0	221	OpenFOAM Pre-Processing
	The convergence problem of IcoFoam with cyclic boundary anhkenyt	September 9, 2020 19:55 by anhkenyt	0	322	OpenFOAM Running, Solving & CFD
	A deep look at cyclic boundary condition in openFoam anhkenyt	June 4, 2020 10:49 by lukasf	1	664	OpenFOAM Programming & Development
	[cfMesh] Cyclic boundary condition with cfMesh lukasf	May 22, 2020 19:19 by spalartallmaras	2	1,540	OpenFOAM Community Contributions
	Cyclic Boundary condition for flow around tubes Dmarcohe	November 21, 2019 14:43 by Dmarcohe	0	421	OpenFOAM Running, Solving & CFD
	Cyclic Symmetry and Periodic Boundary Conditions Yorkshire2019	November 18, 2019 15:46 by AlexLi_HIT_KHAI	7	3,774	FLUENT
	steady free-surface flow simulation interFoam cuikahlil	October 8, 2018 11:21 by cuikahlil	0	617	Main CFD Forum
	Setting cyclicAMI and cyclic Boundary conditions (ICEM Mesh to OpenFoam) bowen1024	March 1, 2018 20:28 by bowen1024	4	3,523	OpenFOAM Pre-Processing
	segmentatio fault using cyclic boundary conditions in FOAM extend 3.2 GFarello	January 18, 2017 06:27 by GFarello	2	1,158	OpenFOAM Running, Solving & CFD
	periodic simulation amintalezade	August 1, 2016 06:45 by amintalezade	5	895	OpenFOAM Running, Solving & CFD
	GAMG with cyclic boundary in parallel = crash rdbisme	April 5, 2016 11:34 by anishtain4	3	1,078	OpenFOAM Running, Solving & CFD
	[mesh manipulation] Problem with using createPatchDict to define cyclic boundaries kaszt	April 1, 2016 22:18 by kaszt	0	1,633	OpenFOAM Meshing & Mesh Conversion
	[snappyHexMesh] Problem creating patches using snappyheymesh kewsinger	November 10, 2014 05:48 by kewsinger	3	1,138	OpenFOAM Meshing & Mesh Conversion
	Problem to run flow around a cylinder - LES case valerio galluzzi	August 29, 2014 06:05 by valerio galluzzi	2	1,144	OpenFOAM Pre-Processing
	Problem to run flow around a cylinder - LES case valerio galluzzi	August 26, 2014 08:47 by valerio galluzzi	0	1,020	OpenFOAM Pre-Processing
	CyclicAMI with half cylinder/ Projection of boundaries OlliWer	December 10, 2013 10:34 by OlliWer	0	1,305	OpenFOAM Pre-Processing
	parallel error with cyclic BCs for pimpleDyMFoam and trouble in resuming running ( 1 2) sunliming	November 22, 2013 04:38 by wyldckat	21	9,403	OpenFOAM Bugs
	Suggestions for a multi region conjugate heat transfer problem maddalena	September 4, 2013 19:03 by math.n3rd91	14	5,920	OpenFOAM
	Katabatic flow using buoyantboussinesqpisofoam tsauter	April 19, 2013 10:09 by tsauter	3	1,368	OpenFOAM
	OF 2.x, cyclic boundary and MRFSimpleFoam compatibility jmf	July 29, 2012 02:51 by vahid.najafi	5	3,519	OpenFOAM Running, Solving & CFD
	Cyclic BC versus directMappedPatch Djub	July 26, 2012 07:29 by Djub	0	1,401	OpenFOAM
	[Other] Cyclic mesh for fully-developed profile fferroni	July 11, 2012 11:49 by zxj160	5	2,398	OpenFOAM Meshing & Mesh Conversion
	[mesh manipulation] createPatch seg-faults when trying on rotationally periodic faces (v2.0.x) vishalsacharya	March 6, 2012 20:32 by vishalsacharya	0	1,491	OpenFOAM Meshing & Mesh Conversion
	How to create a new cyclic BC gregdB	February 10, 2012 10:40 by gregdB	6	2,163	OpenFOAM
	Heat sink specification Barry	January 27, 2012 09:24 by Barry	0	1,243	Main CFD Forum
	Pressure reference in cyclic interFoam AlmostSurelyRob	February 16, 2011 10:58 by nimasam	7	3,536	OpenFOAM
	mass flux in two phase flow nimasam	December 9, 2010 04:48 by nimasam	0	2,219	OpenFOAM
	cyclic patch nimasam	December 1, 2010 04:01 by herbert	1	1,386	OpenFOAM Running, Solving & CFD
	cyclic boundary condition Ibo	November 20, 2009 10:42 by Ibo	0	1,378	FLUENT

All times are GMT -4. The time now is 18:20.