[ANSYS Meshing] Error in Workbench "Unable to attach to geometry file"

heavenlysins · August 12, 2015, 08:14

One more thing,
Do you know anything about applying G loads ?

Kapi · August 12, 2015, 19:53

I dont know much about G load but yea lot of information is available online!

heavenlysins · August 13, 2015, 00:17

hmm, I tried searching for papers but couldn't find any.
Can you help me with any links to papers where i can get some information about it. ?

Kapi · August 13, 2015, 02:35

http://www.researchgate.net/post/How..._load_in_Ansys

check if this is what u r after

heavenlysins · August 13, 2015, 09:33

Thank You so much for the help. It really helps.

abtin · October 28, 2015, 06:02

Dearl all,
I read the following steps (CAD CONFIGURATION) but it doesnt work in my system (ansys 2016 licenecd). bytheway I tried to save my file with diffrent DWG and DXF version.
Do you have any suggestion

absa94 · February 24, 2016, 06:01

when I try to configure solidworks into ansys I get this message "SW Workbench PlugIn ..... Not Configured"
please help...

-Maxim- · February 24, 2016, 06:55

Quote:

Originally Posted by absa94

when I try to configure solidworks into ansys I get this message "SW Workbench PlugIn ..... Not Configured"
please help...

http://lmgtfy.com/?q=SW+Workbench+Pl...Not+Configured

Have you tried the CAD Configuration Manager?
Also, have you read the help chapter
8.1. Using the CAD Configuration Manager

sarkripalu · September 16, 2017, 04:34

Quote:

Originally Posted by diamondx

that is in fact weird. i could load your geometry in ansys meshing without any problem.
i even could see your error. after i double clicked to try, it worked. I googled that and some say that it may be an error due to the installation of ansys: it has to be done under administrator rights.
In one forum i did found some directions:

the CAD configuration manager is in start menu under the ansys 13 branch, I wish i can help more...

how to deal with the error?

sarkripalu · September 16, 2017, 04:37

To avoid error, you just need to run the CAD configuration manager as an administrator. It will be done successfully.

chvenky.001 · October 25, 2017, 16:03

Thankyou very much ......problem has been solved

October 28, 2015, 06:02	Unable to create plug-in perhaps needs registered	#66
abtin New Member abtin hesami Join Date: Oct 2015 Posts: 4 Rep Power: 10	Dearl all, I read the following steps (CAD CONFIGURATION) but it doesnt work in my system (ansys 2016 licenecd). bytheway I tried to save my file with diffrent DWG and DXF version. Do you have any suggestion

February 24, 2016, 06:01	Help!	#67
absa94 New Member bosi Join Date: Feb 2016 Posts: 3 Rep Power: 10	when I try to configure solidworks into ansys I get this message "SW Workbench PlugIn ..... Not Configured" please help...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ANSYS Workbench on "Uncertified" Linux Distros	hsr	CFX	289	April 20, 2023 09:23
Workbench geometry in to ICEM	KM	CFX	2	December 21, 2007 13:45
vitual _ real	deneb	FLUENT	3	January 22, 2007 04:31
workbench geometry in ICEM	Ross	CFX	6	November 2, 2006 06:51
Virtual/Real geometry.	Jack Keays	FLUENT	9	June 15, 2000 23:39

August 12, 2015, 08:14		#61
heavenlysins New Member Join Date: May 2015 Posts: 14 Rep Power: 10	One more thing, Do you know anything about applying G loads ?

August 12, 2015, 19:53		#62
Kapi Senior Member Join Date: Apr 2014 Location: Melbourne Posts: 584 Rep Power: 14	I dont know much about G load but yea lot of information is available online!

August 13, 2015, 00:17		#63
heavenlysins New Member Join Date: May 2015 Posts: 14 Rep Power: 10	hmm, I tried searching for papers but couldn't find any. Can you help me with any links to papers where i can get some information about it. ?

August 13, 2015, 02:35		#64
Kapi Senior Member Join Date: Apr 2014 Location: Melbourne Posts: 584 Rep Power: 14	http://www.researchgate.net/post/How..._load_in_Ansys check if this is what u r after

August 13, 2015, 09:33		#65
heavenlysins New Member Join Date: May 2015 Posts: 14 Rep Power: 10	Thank You so much for the help. It really helps.

September 16, 2017, 04:37		#70
sarkripalu New Member Kripalu Sar Join Date: Jul 2017 Posts: 6 Rep Power: 8	To avoid error, you just need to run the CAD configuration manager as an administrator. It will be done successfully.

October 25, 2017, 16:03		#71
chvenky.001 New Member venky Join Date: Oct 2017 Posts: 1 Rep Power: 0	Thankyou very much ......problem has been solved