|
[Sponsors] |
April 7, 2021, 11:55 |
U-Tube
|
#1 |
New Member
Nikolakis
Join Date: Mar 2021
Posts: 11
Rep Power: 5 |
I can't mesh the green part. Multizone keeps failing. Hexa dominant kinda worked, but am i supposed not to work with hexa dominant in cfd?
Last edited by Zerlox; April 17, 2021 at 12:07. |
|
April 17, 2021, 12:10 |
notice
|
#2 |
New Member
Nikolakis
Join Date: Mar 2021
Posts: 11
Rep Power: 5 |
I have sliced my part like this
|
|
April 21, 2021, 08:27 |
|
#3 |
Senior Member
Join Date: Mar 2009
Location: Norway
Posts: 137
Rep Power: 17 |
Have you tried to sweep it all the way? You might need the inner and outer to start and stop at the same location then, meaning the thinner outer part should be a separate body. But they can be connected through Shared topology.
|
|
April 26, 2021, 08:44 |
|
#4 |
New Member
Nikolakis
Join Date: Mar 2021
Posts: 11
Rep Power: 5 |
if i select explode part the meshing works but if i form a part with all the bodies errors appear. Any help?
|
|
April 26, 2021, 08:51 |
|
#5 |
Senior Member
Join Date: Mar 2009
Location: Norway
Posts: 137
Rep Power: 17 |
It would help if you could explain the reasoning for dividing the geometry the way you have done. I would still recommend to sweep this. Is there a square hollow middle section in the tube?
You may want to share the geometry model as an attachment. |
|
April 29, 2021, 10:48 |
|
#6 |
New Member
Nikolakis
Join Date: Mar 2021
Posts: 11
Rep Power: 5 |
I divided that for a better mesh. If i do not divide it i cannot sweep because sweeping doesn't allow inflation. I will post a picture with multizone, inflation and face meshing.
|
|
April 29, 2021, 10:50 |
|
#7 |
Senior Member
Join Date: Mar 2009
Location: Norway
Posts: 137
Rep Power: 17 |
That is incorrect, you can use inflation with sweeping. Just select face and edge instead of body and face.
|
|
April 29, 2021, 10:53 |
|
#8 |
New Member
Nikolakis
Join Date: Mar 2021
Posts: 11
Rep Power: 5 |
Any recomendations? |
|
April 29, 2021, 14:57 |
|
#9 |
Senior Member
Join Date: Mar 2009
Location: Norway
Posts: 137
Rep Power: 17 |
This seems fine to me, but I don't see why there are several Face meshing and inflations, and still a Multizone. Wouldn't you say it is possible to use the large face you have here as the sweep surface? That would require 1) Sweep method, and 2) Inflation of this single face.
See also https://www.computationalfluiddynami...hing-in-ansys/ |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Defining Boundary Condition of Simulation of Shell and Tube Heat Exchanger ? | miftahazhar | FLUENT | 0 | June 26, 2019 10:34 |
Moving solid in a tube | D2Net15 | CFX | 3 | January 14, 2019 11:12 |
HLL Riemann Shock Tube Matlab Problem | Luke F | Main CFD Forum | 2 | May 20, 2016 02:10 |
[OpenFOAM] Tube filter in Paraview | werweisswas | ParaView | 0 | December 10, 2012 06:18 |
[Other] How to set up a dynamic mesh for a piston moving through a tube of variable diameter? | karkar | OpenFOAM Meshing & Mesh Conversion | 0 | July 4, 2012 06:54 |