|
[Sponsors] |
May 15, 2016, 08:18 |
ansys command * get help
|
#1 |
New Member
davide ilmigliore
Join Date: May 2016
Posts: 1
Rep Power: 0 |
Hi, I created a template using a heatsink ansys APDL , and I calculated the thermal solutions in the event that this heat sink to dissipate heat by convection and conduction and then I calculated the mechanical solution . Then I wanted to ask how I can extract such as the von mises tension through function * get and write this value in a txt file. I also want to extract the value of the temperature and the higher the value of the highest voltage , and write it on a txt file. I have tried using the following code , but it tells me error enough date format ... __________________________________________________ ______ * GET , x , PLNSOL , 0 , max , , , * Cfopen , ' s ' , ' txt ' ,, append * Vwrite , x finish
__________________________________________________ ________ The code around the program without the get function is: finish /clear /filname,dissipatore /prep7 *SET,b,0.0045 *SET,h,0.05 *SET,ba,0.002 *SET,h,0.070 *SET,ba,0.0005 *SET,b,0.001 *SET,adduzione,45 *SET,temp,40 ET,2,PLANE55 !* !* MPTEMP,,,,,,,, MPTEMP,1,0 MPDATA,KXX,1,,365 MPTEMP,,,,,,,, MPTEMP,1,0 MPDATA,KXX,2,,180 RECTNG,0,0.004,0,b, RECTNG,0.004,0.008+b-ba,0,b, RECTNG,0.008+b-ba,h,0,ba, cyl4,0.008+b-ba,b,b-ba,,, asba,2,4 aadd,5,3 aglue,1,2 asel,s,area,,1 aatt,1,,1,0, allsel,all asel,s,area,,3 aatt,2,,1,0, allsel,all aesize,all,ba/5, !Bisogna assegnare gli elementi alle aree: andare su meshing-->mesh attributes-->picked areas--> seleziono l'area 1 !e gli assegno l'elemento 2 plane55 e faccio lo stesso con l'area 2 amesh,all SFL,2,HFLUX,(60*2)/(0.05*0.05), SFL,7,CONV,adduzione, ,temp, SFL,10,CONV,adduzione, ,temp, SFL,11,CONV,adduzione, ,temp, SFL,12,CONV,adduzione, ,temp, finish /sol solve finish /post1 plnsol,temp,,0 !fine parte termica !inizio parte meccanica finish /prep7 lsclear,all etchg,tts mptemp,,,,,,,, mptemp,1,0 uimp,1,reft,,,20 mpdata,alpx,1,,12.5e-6 mptemp,,,,,,,, mptemp,1,0 uimp,2,reft,,,20 mpdata,alpx,2,,24.2e-6 mptemp,,,,,,,, mptemp,1,0 mpdata,ex,1,,110e9 mpdata,prxy,1,,0.35 mptemp,1,0 mpdata,ex,2,,68.9e9 mpdata,prxy,2,,0.33 tb,biso,2,1,2, tbtemp,0 tbdata,,60e6,2200e6,,,, tb,biso,1,1,2, tbtemp,0 tbdata,,60e6,1380e6,,,, dl,4, ,ux,0 dl,1,,uy,0 dl,5,,uy,0 dl,9,,uy,0 lsel,s,line,,3 lsel,a,line,,12 nsll,s,1 !FARE MANUALMENTE: solution-define loads-apply-structural-displacement-on nodes-all-uy !!cp,1,ux,all allsel,all ldread,temp,,, , ,'dissipatore','rth',' ' finish /sol AUTOTS,1 TIME,1 SOLVE |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Pro/E to ANSYS Parameterization Guide | Trues | ANSYS | 4 | April 18, 2018 05:52 |
Can you help me with a problem in ansys static structural solver? | sourabh.porwal | Structural Mechanics | 0 | March 27, 2016 17:07 |
Ansys SIG$ILL error | loth | ANSYS | 3 | December 24, 2015 05:31 |
2-way FSI in Ansys CFX 15 | LucasGasparino | CFX | 3 | August 6, 2015 03:17 |
Exporting results from CFX to ANSYS ?? | sohail ahmed | CFX | 1 | December 20, 2007 01:10 |