|
[Sponsors] |
![]() |
![]() |
#1 |
New Member
Ali
Join Date: Dec 2011
Posts: 21
Rep Power: 15 ![]() |
Hi Guys,
I'm going to move a flat plate up and down sinusoidally in CFX. The simulation is 2D. Does any one know How I should tackle this problem? I will appreciate, if you help me. tnx Ali |
|
![]() |
![]() |
![]() |
![]() |
#2 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,978
Rep Power: 145 ![]() ![]() ![]() ![]() |
Can you post an image of what you want to do? Is the plate vertical or horizontal?
|
|
![]() |
![]() |
![]() |
![]() |
#3 |
New Member
Ali
Join Date: Dec 2011
Posts: 21
Rep Power: 15 ![]() |
Hi,
Sorry for replying late. Please have look at the tutorial posted on " https://www.box.com/shared/jicr9u3jgv". On page 3, you'll see a figure which is similar to my problem. I wan to move the middle zone sinusoidally with a flat plate. Could u please help how I can simulate this problem in CFX? Thanks, Ali |
|
![]() |
![]() |
![]() |
![]() |
#4 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,978
Rep Power: 145 ![]() ![]() ![]() ![]() |
Have a look at the CFX tutorials. Several of them show how to model moving mesh.
|
|
![]() |
![]() |
![]() |
![]() |
#5 |
New Member
Ali
Join Date: Dec 2011
Posts: 21
Rep Power: 15 ![]() |
Hi Glenn,
In CFX we only have two options: stationary domain and rotating domain. In my problem, which is a 2D simulation, I want to move both the fluid within the domain as well as a flat plate sinusoidally up and down. This means that domain itself should also move sinusoidally. The plate in my simulation follows this equation (v=A*sin(wt)), where v is the vertical component of velocity. Do I need to specify the same motion for mesh deformation? (mesh motion> specified displacement> Y=v) Does it make sense? Tnx |
|
![]() |
![]() |
![]() |
![]() |
#6 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,978
Rep Power: 145 ![]() ![]() ![]() ![]() |
The two options you refer to are for rotating frame of reference simulation. You are looking for moving mesh, that is different.
Look at the CFX tutorials for moving mesh examples, not rotating examples. |
|
![]() |
![]() |
![]() |
![]() |
#7 |
Member
Mrinal K R
Join Date: Sep 2011
Location: Chennai, India
Posts: 47
Rep Power: 15 ![]() |
Can you please explain what is the difference between moving mesh and rotating frame of reference simulation with suitable examples?
when and where it is using?? |
|
![]() |
![]() |
![]() |
![]() |
#8 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,978
Rep Power: 145 ![]() ![]() ![]() ![]() |
Moving mesh allows any mesh motion. Rotating mesh only allows rotating motion, which I guess could be considered a sub-set of moving mesh.
|
|
![]() |
![]() |
![]() |
![]() |
#9 |
Member
Mrinal K R
Join Date: Sep 2011
Location: Chennai, India
Posts: 47
Rep Power: 15 ![]() |
Thank you sir..
Can we produce translational along with rotational motion in CFX? I want to create translational and rotational motion of circle in CFX? Is it possible? any similar tutorials are available? |
|
![]() |
![]() |
![]() |
![]() |
#10 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,978
Rep Power: 145 ![]() ![]() ![]() ![]() |
Yes, it is possible but you then have to use general mesh motion. You cannot model translation with rotating frames of reference.
|
|
![]() |
![]() |
![]() |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
running 2D airfoil mesh in CFX | iffy | ANSYS | 1 | February 13, 2011 21:35 |
CFX Moving Mesh Contact "Management" | peppeone | CFX | 3 | January 17, 2011 16:51 |
cfx mesh problem... | mactech001 | ANSYS Meshing & Geometry | 0 | November 5, 2009 02:19 |
Turbulence model for CFX moving mesh | songxguan | CFX | 7 | June 28, 2009 21:05 |
Icemcfd 11: Loss of mesh from surface mesh option? | Joe | CFX | 2 | March 26, 2007 18:10 |