|
[Sponsors] |
August 1, 2017, 03:23 |
warning and converge has stoped
|
#1 |
Member
gasem
Join Date: Jul 2017
Posts: 51
Rep Power: 8 |
hello everyone
when i run my simulation in the first there is this warning WARNING: areas of periodic boundaries 4 and 5 do not match. This may cause mass loss. what dose it mean? and how can i resolve that. second my running after 46 cycle run has stop like this attach file please help me |
|
August 1, 2017, 10:34 |
|
#2 |
Senior Member
Sameera Wijeyakulasuriya
Join Date: Jan 2016
Location: Convergent Science, Madison WI
Posts: 117
Rep Power: 10 |
Period boundaries happen in pairs and their areas should match exactly. Gas and parcel mass that goes out of the domain by one periodic boundary is introduced in to the domain through the other. For this purpose we recommend exact surface triangulation on both periodic surfaces so that the surface areas will be the same. If this condition is not satisfied mass which leaves from one periodic boundary will be be introduced through the other exactly.
|
|
August 1, 2017, 12:41 |
|
#3 |
Member
gasem
Join Date: Jul 2017
Posts: 51
Rep Power: 8 |
hello
how i can do it? |
|
August 1, 2017, 12:48 |
|
#4 |
Senior Member
Sameera Wijeyakulasuriya
Join Date: Jan 2016
Location: Convergent Science, Madison WI
Posts: 117
Rep Power: 10 |
Use "Make Surface" utility in CONVERGE Studio v2.4. The sector made from this utility is guaranteed to have similar area of the two periodic surfaces. If you have not used this feature before, send me your email address and I will send you a document that teaches you how to use it.
|
|
August 1, 2017, 12:56 |
|
#5 |
Member
gasem
Join Date: Jul 2017
Posts: 51
Rep Power: 8 |
my converge studio is v2.2 must i use v2.2 ? i can't do it in v2.2? my mail is jiliyur@yahoo.com
|
|
August 1, 2017, 13:00 |
|
#6 |
Senior Member
Sameera Wijeyakulasuriya
Join Date: Jan 2016
Location: Convergent Science, Madison WI
Posts: 117
Rep Power: 10 |
No, I recommend you using v2.4 Studio. Make surface is not in v2.2 Studio. I sent you the slides on Make surface
|
|
August 1, 2017, 13:59 |
|
#7 |
Member
gasem
Join Date: Jul 2017
Posts: 51
Rep Power: 8 |
thaks alot where can i give studio 2.4 is there in converge site?
|
|
August 1, 2017, 14:38 |
|
#8 |
Senior Member
Sameera Wijeyakulasuriya
Join Date: Jan 2016
Location: Convergent Science, Madison WI
Posts: 117
Rep Power: 10 |
Which company/university are you from? You need login access to our downloads site.
|
|
August 1, 2017, 14:53 |
|
#9 |
Member
gasem
Join Date: Jul 2017
Posts: 51
Rep Power: 8 |
i am in university of sahand i think i need a university mail all right? i loging in your site but i cant find the download section how ever thanks for your reply i will have some question in future i hope to use your good guide againe
|
|
August 3, 2017, 13:18 |
|
#10 |
Senior Member
Tobias
Join Date: May 2016
Location: Germany
Posts: 265
Rep Power: 10 |
||
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Warning: Independent variables were clipped during table generation | Simplyyy | CFX | 4 | May 29, 2020 16:36 |
Converge warning | rsoni451 | CONVERGE | 1 | June 16, 2017 08:42 |
warning - extrapolating on temperature calculation | cedame | CONVERGE | 2 | September 5, 2016 11:55 |
Warning: Surface chemistry solver did not converge | Parisa_Khiabani | FLUENT | 5 | May 3, 2014 11:50 |
On and Off of Reverse flow warning | prince_pahariaa | FLUENT | 1 | December 24, 2011 05:22 |