 |
 |
 |
|
|
|
[Sponsors] | ||||
February 11, 2019, 09:40
|
Post process in Paraview
|
#1 |
|
Member
Join Date: Jun 2016
Posts: 52
Rep Power: 9  |
Hi all,
Can someone please advise on post-processing CONVERGE data in Paraview please? I have converted one single file in CONVERGE to VTK in-line binary format however I have ended up with many different files and not sure where to start. Any input appreciated |
|
|
|
|
|
February 13, 2019, 07:56
|
Paraview with Converge
|
#2 |
|
New Member
Abdellah
Join Date: Mar 2018
Location: France
Posts: 8
Rep Power: 8 |
You have a group a file with ".vtm" at the end. This file you should import to paraview.
Advice : create a specific import for each parameter you want to see, really easy to be handeled by paraview (my point of view). |
|
|
|
|
|
|
February 15, 2019, 05:19
|
|
#3 |
|
Member
Join Date: Jun 2016
Posts: 52
Rep Power: 9 |
Is there any difference in using the "binary" or "ascii" type conversion?
|
|
|
|
|
|
|
February 15, 2019, 05:22
|
Difference ascii binary paraview export
|
#4 |
|
New Member
Abdellah
Join Date: Mar 2018
Location: France
Posts: 8
Rep Power: 8 |
Probably ! But I used both & they both work. I didn't see any difference
|
|
|
|
|
|
|
February 15, 2019, 05:46
|
|
#5 |
|
Member
Join Date: Jun 2016
Posts: 52
Rep Power: 9 |
Also, do you know how to activate the NVIDIA plug-in?
|
|
|
|
|
|
|
May 14, 2019, 06:39
|
Numbers don't add up after converting tp Paraview Format
|
#6 |
|
New Member
Join Date: Apr 2019
Posts: 10
Rep Power: 6 |
I converted the files after running a case of total time 3e-4 s. The case ran until the end the time intervals for writing the output is 5e-5. As expected I have 6 output files. I get a message after converting that says
Please indicate which variables you would like to include: all converting file post000001_+0.00000e+00.out ... numbers don't add up vertex_index, face_per_cell_index, verts_per_face_index = 0 0 0 did the file finish writing? converting file post000002_+5.00048e-05.out ... numbers don't add up vertex_index, face_per_cell_index, verts_per_face_index = 0 0 0 did the file finish writing? converting file post000003_+1.00006e-04.out ... numbers don't add up vertex_index, face_per_cell_index, verts_per_face_index = 0 0 0 did the file finish writing? converting file post000004_+1.50005e-04.out ... numbers don't add up vertex_index, face_per_cell_index, verts_per_face_index = 0 0 0 did the file finish writing? converting file post000005_+2.00001e-04.out ... numbers don't add up vertex_index, face_per_cell_index, verts_per_face_index = 0 0 0 did the file finish writing? converting file post000006_+2.50010e-04.out ... numbers don't add up vertex_index, face_per_cell_index, verts_per_face_index = 0 0 0 did the file finish writing? converting file post000007_+3.00013e-04.out ... numbers don't add up vertex_index, face_per_cell_index, verts_per_face_index = 0 0 0 did the file finish writing? normal termination! Program used 0.000000 seconds The mesh size was reduced and I ave the same issue. Any suggestion? |
|
|
|
|
|
|
May 14, 2019, 09:41
|
|
#7 |
|
Member
Join Date: Jun 2016
Posts: 52
Rep Power: 9 |
Has your output folder updated iwth many different paraview related files since it did the conversion?
|
|
|
|
|
|
|
May 14, 2019, 10:46
|
|
#8 |
|
New Member
Join Date: Apr 2019
Posts: 10
Rep Power: 6 |
it did with only one pvd file
|
|
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Post process Eulerian multiphase model | hamed.majeed | FLUENT | 0 | August 31, 2018 13:47 |
| Spray simulation post process | balaji | OpenFOAM Post-Processing | 5 | August 20, 2016 11:22 |
| Post Process in Fluent | Hamilton | FLUENT | 0 | September 23, 2012 01:03 |
| Post Process in CFX | safikhani_hamed | CFX | 1 | July 12, 2012 08:12 |
| [General] Flow3d post processing with ParaView | Rajiv Kothari | ParaView | 0 | May 24, 2007 09:00 |
Linear Mode
