Can't Select Mesh Interfaces Tab

morais · June 15, 2016, 06:14

Hi everyone,

I'm trying to complete FLUENT tutorial 12 but ran into a wall.

At Step 12.4.8, we are asked to set up the mesh interfaces between the fluid-inlet and fluid-rotor.

However, I can't seem to access the Mesh Interfaces tab.

Hope one of you can help me out. I am very new to this software.

Cheers,
Sean Morais

mesh interfaces.png

Far · June 15, 2016, 17:28

because you dont have interfaces in mesh.

diamondx · June 15, 2016, 19:58

I remember this tutorial , those interior white lines are supposed to be interfaces

Far · June 17, 2016, 05:21

there are two methods.

Interior (one boundary between two domains.

Second method: two different boundaries at same location, later will be defined at interface.

ciftci.ibrahim · June 17, 2016, 06:18

How many cell zone is there in your case?

June 15, 2016, 06:14	Can't Select Mesh Interfaces Tab	#1
morais New Member Sean Join Date: Jun 2016 Posts: 3 Rep Power: 11	Hi everyone, I'm trying to complete FLUENT tutorial 12 but ran into a wall. At Step 12.4.8, we are asked to set up the mesh interfaces between the fluid-inlet and fluid-rotor. However, I can't seem to access the Mesh Interfaces tab. Hope one of you can help me out. I am very new to this software. Cheers, Sean Morais mesh interfaces.png

June 15, 2016, 19:58		#3
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 30	I remember this tutorial , those interior white lines are supposed to be interfaces __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] problems generating clean mesh	Christian_tt	OpenFOAM Meshing & Mesh Conversion	2	June 20, 2019 06:39
[ICEM] Generating Mesh for STL Car in Windtunnel Simulation	tommymoose	ANSYS Meshing & Geometry	48	April 15, 2013 05:24
[Gmsh] 2D Mesh Generation Tutorial for GMSH	aeroslacker	OpenFOAM Meshing & Mesh Conversion	12	January 19, 2012 04:52
[snappyHexMesh] snappyHexMesh won't work - zeros everywhere!	sc298	OpenFOAM Meshing & Mesh Conversion	2	March 27, 2011 22:11
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 12:55

June 15, 2016, 17:28		#2
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,565 Blog Entries: 6 Rep Power: 55	because you dont have interfaces in mesh.

June 17, 2016, 05:21		#4
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,565 Blog Entries: 6 Rep Power: 55	there are two methods. Interior (one boundary between two domains. Second method: two different boundaries at same location, later will be defined at interface.

June 17, 2016, 06:18		#5
ciftci.ibrahim New Member İbrahim Çiftçi Join Date: Apr 2015 Location: TURKEY/KONYA Posts: 4 Rep Power: 12	How many cell zone is there in your case?