Display Error after Scaling Mesh

gerritb · October 18, 2017, 04:15

Hi all,

I accidentally created my surface mesh in ANSA with millimeter (mm) as the length unit instead of meter (m). I already created the volume mesh in TGrid without noticing, and even ran my simulation.

Now I want to fix that mistake and used the 'scale mesh' function in Fluent (under 'general'->'mesh'->'scale'). Unfortunately, now the mesh is not displayed correctly, but seems to be twisted. However, when I compute the area of particular faces or the volume of particular cell zones, the correct value in the correct unit (m2 for area, m3 for volume) is computed. Running the simulation also works without any error message, the solution converges. But also in the post-processing, the display of the model is twisted in the same way as in the mesh.

The fact that everything else works fine leads me to the conclusion, that it is just a display error. Does anyone have an idea what could cause this error, and more importantly how to fix it?

Thanks,
Gerrit

vangelis · October 18, 2017, 10:18

Hi Gerrit.

Do you have just surface mesh in ANSA?
Is it geometry macros or FE-mod mesh?
What do you mean by twisted? Can you post an image?
Have you tried volume meshing in ANSA?

cheers
Vangelis

gerritb · October 18, 2017, 20:33

Hi Vangelis,
Thanks for your reply.

Apparently it was only a display error. Restarting the computer solved the problem. Too easy, didn't considder doing that. Sorry

vangelis · October 19, 2017, 03:54

You may want to check you have the latest graphics driver

October 18, 2017, 04:15	Display Error after Scaling Mesh	#1
gerritb New Member Gerrit B Join Date: Oct 2017 Posts: 8 Rep Power: 7	Hi all, I accidentally created my surface mesh in ANSA with millimeter (mm) as the length unit instead of meter (m). I already created the volume mesh in TGrid without noticing, and even ran my simulation. Now I want to fix that mistake and used the 'scale mesh' function in Fluent (under 'general'->'mesh'->'scale'). Unfortunately, now the mesh is not displayed correctly, but seems to be twisted. However, when I compute the area of particular faces or the volume of particular cell zones, the correct value in the correct unit (m2 for area, m3 for volume) is computed. Running the simulation also works without any error message, the solution converges. But also in the post-processing, the display of the model is twisted in the same way as in the mesh. The fact that everything else works fine leads me to the conclusion, that it is just a display error. Does anyone have an idea what could cause this error, and more importantly how to fix it? Thanks, Gerrit

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[ICEM] 2D hybrid mesh (unstructured mesh highly dependent on structured mesh parameters)	shubham jain	ANSYS Meshing & Geometry	1	April 10, 2017 05:03
[snappyHexMesh] No layers in a small gap	bobburnquist	OpenFOAM Meshing & Mesh Conversion	6	August 26, 2015 09:38
[snappyHexMesh] Layers:problem with curvature	giulio.topazio	OpenFOAM Meshing & Mesh Conversion	10	August 22, 2012 09:03
errors when installing openfoam2.1 on ubuntu12.o4	hewei	OpenFOAM Installation	5	May 29, 2012 07:43
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 11:55

October 18, 2017, 10:18		#2
vangelis Senior Member Vangelis Skaperdas Join Date: Mar 2009 Location: Thessaloniki, Greece Posts: 286 Rep Power: 20	Hi Gerrit. Do you have just surface mesh in ANSA? Is it geometry macros or FE-mod mesh? What do you mean by twisted? Can you post an image? Have you tried volume meshing in ANSA? cheers Vangelis

October 18, 2017, 20:33		#3
gerritb New Member Gerrit B Join Date: Oct 2017 Posts: 8 Rep Power: 7	Hi Vangelis, Thanks for your reply. Apparently it was only a display error. Restarting the computer solved the problem. Too easy, didn't considder doing that. Sorry

October 19, 2017, 03:54		#4
vangelis Senior Member Vangelis Skaperdas Join Date: Mar 2009 Location: Thessaloniki, Greece Posts: 286 Rep Power: 20	You may want to check you have the latest graphics driver