|
[Sponsors] |
June 24, 2005, 12:33 |
FLUENT FUEL CELL MODEL
|
#1 |
Guest
Posts: n/a
|
Hi,All I am using FLUENT Fuel Cell Toolbox to model a single PEM fuel cell stack.When I tried to initialize the model, I got the following error messages. Error: prf-set-var: invalid flonum Error Object: nan
Anyone knows how to solve the problem? Does that mean that I didn't specify all the required material properties correctly? I am desperate. Please help! BC |
|
January 30, 2010, 03:52 |
|
#2 |
New Member
Philip Mprezas ( f.mprezas@yahoo.gr )
Join Date: Jan 2010
Location: Athens, Greece
Posts: 13
Rep Power: 16 |
what version did you use?
|
|
July 12, 2011, 20:25 |
Same issue
|
#3 |
New Member
Shrinivas
Join Date: Jun 2011
Posts: 1
Rep Power: 0 |
I have the same problem when I modified a case in fluent 13.0 and tried to read it in Fluent 12.1.4. I checked the case file is good by opening it in Fluent 13 multiple times. But with Fluent 12.1.4, it gives the same error message:
"Error: %prf-set-var: invalid flonum" Any clue whats going on? Thanks. Shrinivas |
|
July 7, 2013, 12:59 |
|
#4 |
New Member
Roberto Meloni
Join Date: Dec 2012
Posts: 14
Rep Power: 14 |
Hi guys,
Did anyone fix this fluent bug? I'm running a simulation on Ansys 13 of an internal combustion engine and when I try to load the .cas and .dat files saved every 15 time step, this error message appears. Thanks in advance. All the best. Rob. |
|
May 17, 2014, 19:27 |
|
#5 |
New Member
YuHuo
Join Date: May 2014
Location: Hoboken
Posts: 1
Rep Power: 0 |
Probably because of the different version of Fluent.
|
|
November 22, 2016, 02:23 |
cylinder
|
#6 |
New Member
sanju
Join Date: Nov 2016
Posts: 19
Rep Power: 10 |
I too have the same problem.
I just considered the cylinder and given inlet velocity at one side and outlet pressure at the other side. 1. defined the surfaces as the temperature body 2. inlet air velocity 8 m/s. 3. trying to find the cooling response of the system. In cell zone BC when I define cylinder as fluid then there was no error, but I defined it as solid the error was showing as below Error - %prf-set-var: invalid flonum Error object - 1.£ inf Kindly anyone suggest what is the problem. Thanks in advance. |
|
November 22, 2016, 02:24 |
|
#7 |
New Member
sanju
Join Date: Nov 2016
Posts: 19
Rep Power: 10 |
I am working in ANSYS Fluent 15 version
|
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fuel cell | Rekha | FLUENT | 10 | September 27, 2018 08:52 |
Superlinear speedup in OpenFOAM 13 | msrinath80 | OpenFOAM Running, Solving & CFD | 18 | March 3, 2015 06:36 |
Fluent on Cell Processor | DC | FLUENT | 2 | March 14, 2008 13:01 |
Questions about Fuel cell model | braket | FLUENT | 0 | March 17, 2007 20:37 |
[Commercial meshers] Trimmed cell and embedded refinement mesh conversion issues | michele | OpenFOAM Meshing & Mesh Conversion | 2 | July 15, 2005 05:15 |