EULER simulation

November 7, 2005, 13:18

Hi, I want to simulate an EULER's flow on a plane. Could you explain me the various stages to be followed! Both grid and boundary conditions (wall, sym.,Pressure_inlet, Pressure_outlet) are made with Gambit. I would like just the differents steps with Fluent! (N.B: absolute speed is 340 m/s) Thank you for your help!

Alexandre.

November 8, 2005, 03:59

Please, it's very important! Help me! Alexandre.

November 8, 2005, 05:49

Hi, I want to simulate an EULER's flow on a plane. Could you explain me the various stages to be followed! Both grid and boundary conditions (wall, sym.,Pressure_inlet, Pressure_outlet) are made with Gambit. I would like just the differents steps with Fluent! (N.B: absolute speed is 340 m/s) Thank you for your help!

Alexandre.

November 8, 2005, 06:24

About mesh, there are the following tutorials of gambit that could help you: 5, 6 and 14. About fluent, you should try the tutorial 3.

HV

November 24, 2005, 15:01

Check out the Full Multigrid Initialization in Fluent - this solves the EULER equations to give a better starting point for the Navier-Stokes solver.

November 7, 2005, 13:18	EULER simulation	#1
Alexandre Guest Posts: n/a	Hi, I want to simulate an EULER's flow on a plane. Could you explain me the various stages to be followed! Both grid and boundary conditions (wall, sym.,Pressure_inlet, Pressure_outlet) are made with Gambit. I would like just the differents steps with Fluent! (N.B: absolute speed is 340 m/s) Thank you for your help! Alexandre.

November 8, 2005, 03:59	Re: EULER simulation	#2
Alexandre Guest Posts: n/a	Please, it's very important! Help me! Alexandre.

November 8, 2005, 05:49	eulerian's simulation	#3
Alexandre Guest Posts: n/a	Hi, I want to simulate an EULER's flow on a plane. Could you explain me the various stages to be followed! Both grid and boundary conditions (wall, sym.,Pressure_inlet, Pressure_outlet) are made with Gambit. I would like just the differents steps with Fluent! (N.B: absolute speed is 340 m/s) Thank you for your help! Alexandre.

November 8, 2005, 06:24	Re: eulerian's simulation	#4
HVN Guest Posts: n/a	About mesh, there are the following tutorials of gambit that could help you: 5, 6 and 14. About fluent, you should try the tutorial 3. HV

November 24, 2005, 15:01	Re: eulerian's simulation	#5
Riaan Guest Posts: n/a	Check out the Full Multigrid Initialization in Fluent - this solves the EULER equations to give a better starting point for the Navier-Stokes solver.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Why my simulation not agree with the wind tunnel experiment	zhaowei	CFX	4	July 11, 2015 04:36
Simulation of a complex wing in solidworks flow simulation	niels1900	FloEFD, FloWorks & FloTHERM	6	April 20, 2011 11:44
GUI crash and simulation engine still running	RPJones	FLOW-3D	2	November 9, 2010 09:18
velocity profile export from a simulation onto another	sudhirlv	STAR-CCM+	1	September 12, 2010 19:57
strange simulation error	Ralf Schmidt	FLUENT	2	May 4, 2007 14:02