|
[Sponsors] |
May 13, 2007, 00:17 |
water spray in hot air
|
#1 |
Guest
Posts: n/a
|
Hi, I would like to analyze cooling of hot air using high pressurized water spray. The water droplets are supposed to evaporate inside the duct. Can anyone please help me out, how to set the model. or if there is any related documents (tut file) regarding that in fluent. Thanks in advance.
K |
|
May 22, 2007, 15:36 |
Re: water spray in hot air
|
#2 |
Guest
Posts: n/a
|
I hope you got the answer already. If not, you can use pressure-swirl atmizer or single orifice atomizer in discrete phase model or whichever best suits your need. Select DROPLET (amongst INERT, DROPLET and COMBUSTING). You can follow tutorial "Modeling Evaporating Liquid Spray".
- Prasad |
|
May 23, 2007, 01:55 |
Re: water spray in hot air
|
#3 |
Guest
Posts: n/a
|
hi prasad, thanks for your reply. my problem is still hanging. i tried to follow liquid spray model, but most probably i am not able to set the material properly as i need water air mixture. after doing a trial solve following the above mentined tut, i didn't get the liquid spray at all. i don't know eher i am doin the mistake. also the temperature effect is not playing any role. the energy eqn residual shows very less value compared to others. i m doubtful whether my model is considering the energy effect properly or not. as my problem has a significant role on energy equation, air temp is 500 deg C, water droplets are at low temp(of the order of room temp but at high pressure). can i send you my specific requirement so that u can put yr valuable suggestions on it? plz reply. thanks again. regards, krish
|
|
May 23, 2007, 06:40 |
Re: water spray in hot air
|
#4 |
Guest
Posts: n/a
|
Please send.
|
|
August 10, 2009, 13:06 |
|
#5 |
New Member
pinho
Join Date: May 2009
Posts: 22
Rep Power: 17 |
hi there..
i am studying same case and i dont know what i am doing wrong. can you sent to me any case file? thanks ins advance jpinho |
|
March 13, 2012, 02:57 |
|
#6 |
New Member
Texas
Join Date: Feb 2012
Posts: 5
Rep Power: 14 |
Hey, I am doing the same kind of work. I am able to set the water-air mixture as a material property for species but I am having trouble for DPM mass convergence. Can anyone help me on this issue and I am getting good convergence for energy. I don't whether I am doing any mistake while specifying the material properties. As seen from the above post that Prasad and Kirsh have already done these kind of work...so please help me guys..... I would appreciate you in advance for that.
|
|
April 3, 2013, 09:58 |
|
#7 | |
New Member
afarnoud
Join Date: Apr 2013
Posts: 2
Rep Power: 0 |
Quote:
|
||
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Boiling of water with hot air | Dr. Flow Squad | CFX | 2 | July 27, 2009 08:37 |
air bubble is disappear increasing time using vof | xujjun | CFX | 9 | June 9, 2009 08:59 |
Water jet in confined hot air cross flow | Jim Clancy | FLUENT | 0 | November 24, 2007 17:14 |
water injection into air (not spray) | bioman66 | CFX | 1 | July 11, 2006 07:34 |
Help!!!problems in air jet into water bath | kim | FLUENT | 4 | June 9, 2003 08:04 |