|
[Sponsors] |
September 11, 2008, 16:51 |
Greatly Urgent!!!!! Help me please.
|
#1 |
Guest
Posts: n/a
|
Dear Everybody
I am simulating an unsteady flow through a pipe. The cross-sectional area reduces to 10 percent in the middle. I mean the area is one tenth of the area at the begining or the end of the pipe. I can not converge the problem in any method. I try changing any possible parameter, but the problem diverged. Could you please help me. I should also mention that I analyzed the problem very well with 50 percent area reduction. I need your help as soon as possible. Thanks a lot. |
|
September 12, 2008, 08:28 |
Re: Greatly Urgent!!!!! Help me please.
|
#2 |
Guest
Posts: n/a
|
Try SIMPLEC if not used so far.
|
|
September 12, 2008, 13:27 |
Re: Greatly Urgent!!!!! Help me please.
|
#3 |
Guest
Posts: n/a
|
Dear K.K.Singh
I appreciate your answer. I used the SIMPLEC, but the problem did not converged. If you have any other idea please make me known. Do you know where I can refer to? Thanks a lot. |
|
September 12, 2008, 16:37 |
Re: Greatly Urgent!!!!! Help me please.
|
#4 |
Guest
Posts: n/a
|
Give more details like grids used, turbulence model, under relaxation factors etc. Have u tried node based gradient option instead of cell based gradient option? Try to refine mesh near the constriction by using adapt mesh command.
|
|
September 13, 2008, 01:57 |
Re: Greatly Urgent!!!!! Help me please.
|
#5 |
Guest
Posts: n/a
|
Dear K.K.Singh
I have used the Hex/Cooper mesh in the volume. The viscous model is laminar, but as I have checked the Reynolds number in the throat last night, it was over 10000, so the flow is turbulent. Does it make much error, if I use the laminar model for simulation? Under relaxation factors are set as default in Fluent. I mean pressure=0.3 , density=1 , body force=1 , and momentum=0.7. I should also mention that I have refined the mesh near the throat, but no improvement occured. By the way, where can I change node based gradient option to cell based gradient option? Thanks a lot. |
|
September 13, 2008, 02:05 |
Re: Greatly Urgent!!!!! Help me please.
|
#6 |
Guest
Posts: n/a
|
I forgot an item. If I need to use the turbulent model, please introduce the best one and tell me how to set related parameters?
Regards. |
|
September 20, 2008, 06:51 |
Re: Greatly Urgent!!!!! Help me please.
|
#7 |
Guest
Posts: n/a
|
you can set your turbulence model by using fluent menu DEFINE-Model-Visous, from that select the required turbulance model, The most used model is K-epsilon 2 equation model.Since you are dealing with pipe problem you have set the turbulence intensity and Hydarulic diameter in your boundary condition panel.
|
|
September 29, 2008, 15:19 |
Re: Greatly Urgent!!!!! Help me please.
|
#8 |
Guest
Posts: n/a
|
Use finer mesh.
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Urgent, Urgent, a UDF problem, PLEASE HELP!!! | Max | FLUENT | 1 | September 24, 2010 20:30 |
UDF help urgent | sam | FLUENT | 0 | June 14, 2007 09:46 |
need paper very urgent humanity,very urgent,urgent | mohamed | FLUENT | 0 | August 9, 2006 11:40 |
tmerge urgent urgent | jessica | FLUENT | 4 | July 15, 2006 13:37 |
Urgent | Brandy | FLUENT | 2 | January 8, 2003 01:58 |