CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

gas leak_rhoReactingBuoyantFoam

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   August 12, 2020, 10:55
Question gas leak_rhoReactingBuoyantFoam
  #1
Member
 
nikhil108's Avatar
 
Nikhil
Join Date: May 2020
Location: Freiburg
Posts: 43
Rep Power: 6
nikhil108 is on a distinguished road
Hallo foamers,

I am trying to simulate propane leak from a hole inside a box, which is located in a big computational domain. Whole computational domain has air, and propane starts to leak at 5g/s inside the box. For this I am using rhoReactingBuoyantFoam solver with reactions off. The problem is, after some time propane stops from leak, and there is no change in the leaked jet. It’s like, it got freezed. I tried different boundary conditions, but seems no change. If I change the position of the leak to outside the box then it seems working (not sure). With some changes in the geometry of the box like adding some more outlets, propane jet develops little bit more, but after some time it stops leaking, same as before. What might be the possible reasons for this behavior?.

This jet image attached below is after 4 sec of simulation, after that it stopped over there, the simulation is running, also there is change in velocity field but no change in propane. And the integrated propane flux values (in paraview) also stuck at 4 sec. The other jet image is, when the leak is located outside the box. The box, boundaries are walls. And this box is in a big computational domain, the propane is supposed to leak inside the box and flow out after some time. But that’s not happening . The case files are attached below. I am stuck here, any suggestions ?

case files:
https://www.dropbox.com/s/cjf6oy2bznl5ni0/case.7z?dl=0
Attached Images
File Type: jpg geom01.jpg (32.2 KB, 3 views)
File Type: jpg geom02.jpg (29.6 KB, 3 views)
File Type: jpg C3H8jet_4sec.jpg (9.6 KB, 2 views)
File Type: jpg C3H8jet_4sec_outside_inlet.jpg (24.3 KB, 4 views)
nikhil108 is offline   Reply With Quote

Old   August 12, 2020, 12:32
Default
  #2
Member
 
nikhil108's Avatar
 
Nikhil
Join Date: May 2020
Location: Freiburg
Posts: 43
Rep Power: 6
nikhil108 is on a distinguished road
Thread solved. The residulas are not tight enough.

cheers,
Nikhil.
nikhil108 is offline   Reply With Quote

Reply

Tags
gas leak, openfoam, rhoreactingbuoyantfoam

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Setting the height of the stream in the free channel kevinmccartin CFX 12 October 13, 2022 22:43
Domain Reference Pressure and mass flow inlet boundary AdidaKK CFX 75 August 20, 2018 06:37
error message cuteapathy CFX 14 March 20, 2012 07:45
Constant velocity of the material Sas CFX 15 July 13, 2010 09:56
Gas pressure question Dan Moskal Main CFD Forum 0 October 24, 2002 23:02


All times are GMT -4. The time now is 01:20.