[Helyx OS] Paraview can't find mesh

ld1305 · June 27, 2020, 13:24

I've been looking at using Helyx OS for the first time today, but keep running into a problem quite early on.

I've generated a bounding box, imported an STL to sit inside it, and generated a mesh. The mesh check comes back as OK. At this point I'd ideally like to view the mesh to have a look at the boundary, so I save and move to the Solver tab and open ParaView.

At this point I get the following error:

ERROR: In /home/ubuntu/OpenFOAM/OpenFOAM-7/applications/utilities/postProcessing/graphics/PVReaders/PVFoamReader/vtkPVFoamReader.cxx, line 202
vtkPVFoamReader (0x557b30e089a0): could not find valid OpenFOAM mesh

ERROR: In /home/ubuntu/OpenFOAM/ThirdParty-dev/ParaView-5.6.0/VTK/Common/ExecutionModel/vtkExecutive.cxx, line 779
vtkPVCompositeDataPipeline (0x557b36171520): Algorithm vtkPVFoamReader(0x557b30e089a0) returned failure for request: vtkInformation (0x557b342d3010)
Debug: Off
Modified Time: 221672
Reference Count: 1
Registered Events: (none)
Request: REQUEST_INFORMATION
ALGORITHM_AFTER_FORWARD: 1
FORWARD_DIRECTION: 0

Any help is much appreciated, I'm possibly missing something pretty simple due to inexperience

If it helps, I'm using Helyx OS 2.4.0 with OpenFOAM 7

silambarasan7 · September 6, 2020, 05:00

I am also getting same error

cleitontrindade · January 11, 2022, 18:24

I was also having this problem, and I reduced the domain and it solved

June 27, 2020, 13:24	Paraview can't find mesh	#1
ld1305 Member Lauren Dransfield Join Date: Jan 2012 Posts: 50 Rep Power: 13	I've been looking at using Helyx OS for the first time today, but keep running into a problem quite early on. I've generated a bounding box, imported an STL to sit inside it, and generated a mesh. The mesh check comes back as OK. At this point I'd ideally like to view the mesh to have a look at the boundary, so I save and move to the Solver tab and open ParaView. At this point I get the following error: ERROR: In /home/ubuntu/OpenFOAM/OpenFOAM-7/applications/utilities/postProcessing/graphics/PVReaders/PVFoamReader/vtkPVFoamReader.cxx, line 202 vtkPVFoamReader (0x557b30e089a0): could not find valid OpenFOAM mesh ERROR: In /home/ubuntu/OpenFOAM/ThirdParty-dev/ParaView-5.6.0/VTK/Common/ExecutionModel/vtkExecutive.cxx, line 779 vtkPVCompositeDataPipeline (0x557b36171520): Algorithm vtkPVFoamReader(0x557b30e089a0) returned failure for request: vtkInformation (0x557b342d3010) Debug: Off Modified Time: 221672 Reference Count: 1 Registered Events: (none) Request: REQUEST_INFORMATION ALGORITHM_AFTER_FORWARD: 1 FORWARD_DIRECTION: 0 Any help is much appreciated, I'm possibly missing something pretty simple due to inexperience If it helps, I'm using Helyx OS 2.4.0 with OpenFOAM 7

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
decomposePar problem: Cell 0contains face labels out of range	vaina74	OpenFOAM Pre-Processing	37	July 20, 2020 06:38
Dont find the converge in NACA0012 with structured mesh	ynos	OpenFOAM Running, Solving & CFD	2	December 14, 2013 07:03
[Gmsh] gmshToFoam problem: not the same mesh in Gmsh vs. paraview	zhernadi	OpenFOAM Meshing & Mesh Conversion	8	July 7, 2011 03:28
Errors running allwmake in OpenFOAM141dev with WM_COMPILE_OPTION%3ddebug	unoder	OpenFOAM Installation	11	January 30, 2008 21:30
Icemcfd 11: Loss of mesh from surface mesh option?	Joe	CFX	2	March 26, 2007 19:10

September 6, 2020, 05:00		#2
silambarasan7 Member sila Join Date: Jul 2013 Posts: 32 Rep Power: 11	I am also getting same error

January 11, 2022, 18:24		#3
cleitontrindade New Member Estudante Join Date: Aug 2020 Posts: 1 Rep Power: 0	I was also having this problem, and I reduced the domain and it solved