|
[Sponsors] |
February 23, 2012, 12:02 |
CheckMesh
|
#1 |
Senior Member
Goutam Saha
Join Date: Dec 2011
Location: UK
Posts: 131
Rep Power: 14 |
Dear friends, I am getting following massage using CheckMesh command:
Please see the highlighted line (red color): Do you know why this is happening? Create time Create polyMesh for time = 0 Time = 0 Mesh stats points: 4851 faces: 12800 internal faces: 11200 cells: 4000 boundary patches: 5 point zones: 0 face zones: 0 cell zones: 0 Overall number of cells of each type: hexahedra: 4000 prisms: 0 wedges: 0 pyramids: 0 tet wedges: 0 tetrahedra: 0 polyhedra: 0 Checking topology... Boundary definition OK. ***Total number of faces on empty patches is not divisible by the number of cells in the mesh. Hence this mesh is not 1D or 2D. Cell to face addressing OK. Point usage OK. Upper triangular ordering OK. Face vertices OK. Number of regions: 1 (OK). Checking patch topology for multiply connected surfaces ... Patch Faces Points Surface topology topWall 80 105 ok (non-closed singly connected) bottomWall 80 105 ok (non-closed singly connected) leftWall 80 105 ok (non-closed singly connected) rightWall 80 105 ok (non-closed singly connected) frontAndBack 400 462 ok (non-closed singly connected) Checking geometry... Overall domain bounding box (0 0 0) (10 5 10) Mesh (non-empty, non-wedge) directions (1 0 1) Mesh (non-empty) directions (1 0 1) All edges aligned with or perpendicular to non-empty directions. Boundary openness (0 0 0) OK. Max cell openness = 0 OK. Max aspect ratio = 1 OK. Minumum face area = 0.25. Maximum face area = 0.25. Face area magnitudes OK. Min volume = 0.125. Max volume = 0.125. Total volume = 500. Cell volumes OK. Mesh non-orthogonality Max: 0 average: 0 Non-orthogonality check OK. Face pyramids OK. Max skewness = 1.9984e-14 OK. Coupled point location match (average 0) OK. Mesh OK. End |
|
February 24, 2012, 10:56 |
|
#2 |
Disabled
Join Date: Mar 2011
Posts: 174
Rep Power: 15 |
It is quite self-explanatory.
checkMesh first checks if the mesh is 1D or 2D. Let me guess... you have a 3D mesh! :-) |
|
February 24, 2012, 11:22 |
|
#3 |
Senior Member
Goutam Saha
Join Date: Dec 2011
Location: UK
Posts: 131
Rep Power: 14 |
I have solved my problem. I copied the problem and then changed the blockMeshDict file. So, when I did blockMesh, its not reading my present file (2D mesh). Finally I kill my present file and created a new blockMeshDict file. After that I found its working.
Thanks |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[Other] CheckMesh vs CheckMesh -allGeometry -allTopology | Nagesh Atreyas | OpenFOAM Meshing & Mesh Conversion | 2 | June 25, 2019 04:55 |
checkMesh / mesh errors | andybond13 | OpenFOAM Pre-Processing | 0 | June 10, 2015 13:05 |
[mesh manipulation] checkMesh Erros after refineMesh | mgdenno | OpenFOAM Meshing & Mesh Conversion | 10 | October 14, 2014 05:16 |
[Technical] checkMesh states mesh is OK yet faces are bent pentagons | assert | OpenFOAM Meshing & Mesh Conversion | 1 | March 24, 2014 09:10 |
checkMesh Errors after refineMesh | mgdenno | OpenFOAM | 0 | July 30, 2012 21:39 |