Resin transfer molding process simulation using openfoam

uuivw · May 18, 2014, 10:48

Hello everyone
I am studying how to simulate resin flow into fiber , but I can't get a good software to slove this ,I want use openfoam to slove this ,if anyone did this before,please help me ,how to realize control volume / finite element method by openfoam,thank you very much~~

Regards;

John Degenkolb · May 21, 2014, 07:34

Hi Liaoning,

I'm just about to do so. I'm using OpenFoam's porousInterFoam solver, which is capable to simulate a transient flow of two liquids though a porous permeable medium.
Furthermore there is the ESI Pam-RTM software, which you could use to simulate the standard RTM process. It's quite user friendly, but not generic. What exactly are you trying to do?

Kind regards.

uuivw · May 21, 2014, 08:13

Quote:

Originally Posted by John Degenkolb

Hi Liaoning,

I'm just about to do so. I'm using OpenFoam's porousInterFoam solver, which is capable to simulate a transient flow of two liquids though a porous permeable medium.
Furthermore there is the ESI Pam-RTM software, which you could use to simulate the standard RTM process. It's quite user friendly, but not generic. What exactly are you trying to do?

Kind regards.

Thanks for your concern , But I have searched many times in google ,But I can't find the ESI Pam-RTM software download Link ,Could you tell me how to download the software ,thanks you very much ,and can we talk further about RTM process simulation and optimization, thanks you again~~~~

John Degenkolb · May 21, 2014, 09:14

ESI Pam-RTM is not open source software, so you have to buy it rather than simply download it. I think that there are academic licenses for universities, but no students licenses available.

uuivw · May 21, 2014, 10:15

Quote:

Originally Posted by John Degenkolb

ESI Pam-RTM is not open source software, so you have to buy it rather than simply download it. I think that there are academic licenses for universities, but no students licenses available.

Oh， Thank you first ,I also heared that LIMS was able to simulate the process,and there many papers mentioned the software ,But I can;t get it , Do you know where can I get it ?I want to simulate voids and optimize gate location...,It will be more convenient for me to do it with LIMS Sys...

santoo_cfd · June 6, 2014, 09:02

For LIMS:

http://www.ccm.udel.edu/Pubs/techbriefs/102.html

Though LIMS is also not freeware, it can be used if the problem size is smaller for limited time (Trail licence).

Good luck.

uuivw · June 6, 2014, 09:18

Quote:

Originally Posted by santoo_cfd

For LIMS:

http://www.ccm.udel.edu/Pubs/techbriefs/102.html

Though LIMS is also not freeware, it can be used if the problem size is smaller for limited time (Trail licence).

Good luck.

Hi,
thank you very much , I also know this page ,But I can't find the download link in this page ,can you tell me how to download this software,thanks you

santoo_cfd · June 6, 2014, 12:46

http://www.ccm.udel.edu/Tech/LIMS/

samiam1000 · February 5, 2015, 17:08

Hi there,

by chance, did anyone solve this problem using OpenFOAM?

Thanks a lot,

Samuele.

May 18, 2014, 10:48	Resin transfer molding process simulation using openfoam	#1
uuivw New Member Liaoning Join Date: May 2014 Posts: 12 Rep Power: 12	Hello everyone I am studying how to simulate resin flow into fiber , but I can't get a good software to slove this ,I want use openfoam to slove this ,if anyone did this before,please help me ,how to realize control volume / finite element method by openfoam,thank you very much~~ Regards; Last edited by wyldckat; June 6, 2014 at 14:25. Reason: removed font formatting, because the font was too big

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Suggestion for a new sub-forum at OpenFOAM's Forum	wyldckat	Site Help, Feedback & Discussions	20	October 28, 2014 09:04
Heat transfer simulation of exhaust manifold	Phili	CFX	30	June 12, 2014 02:40
Question on transient simulation in OpenFOAM and FLUENT	nicklj	OpenFOAM Running, Solving & CFD	4	May 8, 2014 22:30
Question about heat transfer simulation	Anna Tian	Main CFD Forum	0	January 25, 2013 18:53
How to transfer boundary condition from Openfoam to fluent	sachinlb	OpenFOAM Post-Processing	1	January 6, 2012 01:41

May 21, 2014, 07:34		#2
John Degenkolb New Member Peter Join Date: Apr 2014 Posts: 21 Rep Power: 13	Hi Liaoning, I'm just about to do so. I'm using OpenFoam's porousInterFoam solver, which is capable to simulate a transient flow of two liquids though a porous permeable medium. Furthermore there is the ESI Pam-RTM software, which you could use to simulate the standard RTM process. It's quite user friendly, but not generic. What exactly are you trying to do? Kind regards.

May 21, 2014, 09:14		#4
John Degenkolb New Member Peter Join Date: Apr 2014 Posts: 21 Rep Power: 13	ESI Pam-RTM is not open source software, so you have to buy it rather than simply download it. I think that there are academic licenses for universities, but no students licenses available.

June 6, 2014, 09:02		#6
santoo_cfd Member santhosh Join Date: Apr 2009 Location: India Posts: 70 Rep Power: 18	For LIMS: http://www.ccm.udel.edu/Pubs/techbriefs/102.html Though LIMS is also not freeware, it can be used if the problem size is smaller for limited time (Trail licence). Good luck.

June 6, 2014, 12:46		#8
santoo_cfd Member santhosh Join Date: Apr 2009 Location: India Posts: 70 Rep Power: 18	http://www.ccm.udel.edu/Tech/LIMS/

February 5, 2015, 17:08		#9
samiam1000 Senior Member Samuele Z Join Date: Oct 2009 Location: Mozzate - Co - Italy Posts: 520 Rep Power: 19	Hi there, by chance, did anyone solve this problem using OpenFOAM? Thanks a lot, Samuele.