Komega turbulent viscosity model

May 17, 2006, 12:02

Hello all,

First of all thank you very much for this great software!
Does someone know if there is a k-omega-model available in OpenFoam?
I need this model to simulate a hard wall as a turbulent viscosity model.

Any help is appreciated.

Daniel

kumar2 · May 17, 2006, 18:57

Hi daniel

did you take a look in the file turbulenceProperties under /constant directory

i was not able to see k-omega in that

regards
kumar

May 18, 2006, 16:31

Hello Kumar,

thank you for the quick reply.
Yes I had a look in this file before posting this thread. The problem is, there is only a simple k-Epsilon model available, but I need the k-omega model instead because it`s better when simulating a hard wall turbulence situation.
But I also tried to use the LaunderGibsonRSTM but I have to figure out first which config files (k,epsilon, R) are exactly neccessary when using LaunderGibsonRSTM.

Daniel
Could someone give me hint?

kumar2 · May 18, 2006, 21:07

Hi Daniel

Please look in /OpenFOAM-1.2/src/turbulenceModels/incompressible/LaunderGibsonRSTM ( or have you already done this ?? ).

looks like the model needs all the 3!

kumar

May 17, 2006, 12:02	Hello all, First of all tha	#1
guggi Guest Posts: n/a	Hello all, First of all thank you very much for this great software! Does someone know if there is a k-omega-model available in OpenFoam? I need this model to simulate a hard wall as a turbulent viscosity model. Any help is appreciated. Daniel

May 17, 2006, 18:57	Hi daniel did you take a lo	#2
kumar2 Senior Member kumar Join Date: Mar 2009 Posts: 112 Rep Power: 18	Hi daniel did you take a look in the file turbulenceProperties under /constant directory i was not able to see k-omega in that regards kumar

May 18, 2006, 16:31	Hello Kumar, thank you for	#3
guggi Guest Posts: n/a	Hello Kumar, thank you for the quick reply. Yes I had a look in this file before posting this thread. The problem is, there is only a simple k-Epsilon model available, but I need the k-omega model instead because it`s better when simulating a hard wall turbulence situation. But I also tried to use the LaunderGibsonRSTM but I have to figure out first which config files (k,epsilon, R) are exactly neccessary when using LaunderGibsonRSTM. Daniel Could someone give me hint?

May 18, 2006, 21:07	Hi Daniel Please look in /O	#4
kumar2 Senior Member kumar Join Date: Mar 2009 Posts: 112 Rep Power: 18	Hi Daniel Please look in /OpenFOAM-1.2/src/turbulenceModels/incompressible/LaunderGibsonRSTM ( or have you already done this ?? ). looks like the model needs all the 3! kumar

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Turbulent viscosity Limited to viscosity ratio	Adrian	FLUENT	12	September 21, 2011 05:22
KOmega Turbulence model from wwwopenFOAMWikinet	philippose	OpenFOAM Running, Solving & CFD	30	August 4, 2010 11:26
best viscosity turbulent model?	Greg	FLUENT	2	October 5, 2007 09:59
Komega turbulence model	jasonb	OpenFOAM Running, Solving & CFD	6	August 29, 2006 09:46
turbulent viscosity limited to viscosity ratio	mukkarum	FLUENT	3	May 11, 2004 05:05