|
[Sponsors] |
[OpenFOAM] ./Allrun: 24: ./Allrun: cannot create /opt/openfoam220/etc/controlDict: |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
August 19, 2013, 07:49 |
|
#24 |
Member
david
Join Date: Jun 2013
Location: Montreal, Canada
Posts: 62
Rep Power: 11 |
Million Thanks Bruno, I check blockMesh it works fine. I can understand up to step 4.4 , the results are below
Code:
toshiba@ubuntu:~/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder$ ./Allrun Modifying /home/toshiba/.OpenFOAM/2.1.0/controlDict to enable allowSystemOperations Enabling allowSystemOperations in /home/toshiba/.OpenFOAM/2.1.0/controlDict. Running blockMesh on /home/toshiba/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder Running potentialFoam on /home/toshiba/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder Running streamFunction on /home/toshiba/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder toshiba@ubuntu:~/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder$ potentialFoam -writep /*---------------------------------------------------------------------------*\ | ========= | | | \\ / F ield | OpenFOAM: The Open Source CFD Toolbox | | \\ / O peration | Version: 2.1.0 | | \\ / A nd | Web: www.OpenFOAM.org | | \\/ M anipulation | | \*---------------------------------------------------------------------------*/ Build : 2.1.0-0bc225064152 Exec : potentialFoam -writep Date : Aug 19 2013 Time : 17:04:41 Host : "ubuntu" PID : 3157 Case : /home/toshiba/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder nProcs : 1 sigFpe : Enabling floating point exception trapping (FOAM_SIGFPE). fileModificationChecking : Monitoring run-time modified files using timeStampMaster allowSystemOperations : Allowing user-supplied system call operations // * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * // Create time Create mesh for time = 0 Reading field p Reading field U Calculating potential flow Using dynamicCode for functionObject difference at line 53 in "/home/toshiba/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder/system/controlDict::functions::difference" DICPCG: Solving for p, Initial residual = 1, Final residual = 7.87068e-07, No Iterations 76 DICPCG: Solving for p, Initial residual = 0.0126096, Final residual = 7.71198e-07, No Iterations 64 DICPCG: Solving for p, Initial residual = 0.0025829, Final residual = 9.49278e-07, No Iterations 59 DICPCG: Solving for p, Initial residual = 0.000902306, Final residual = 8.48077e-07, No Iterations 57 continuity error = 3.37204e-05 Interpolated U error = 1.1896e-05 Looking up field U Reading inlet velocity uInfX U at inlet = 1 m/s Cylinder radius = 0.499614 m Evaluating analytical solution Writing relative error in U to "/home/toshiba/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder/0/error" ExecutionTime = 0.08 s ClockTime = 0 s End toshiba@ubuntu:~/OpenFOAM/toshiba-2.1.0/run/tutorials/basic/potentialFoam/cylinder$ Code:
There is no other time folder, because potentialFoam is an extremely basic folder that loads and saves the results to the same time folder.
__________________
Million Thanks, David "Small Dream is a Crime" |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Using createPatch and cyclicAMI in FOAM Extend to create periodicbox | manuc | OpenFOAM Running, Solving & CFD | 1 | April 12, 2022 11:36 |
create the file *.foam | phongstar | OpenFOAM | 12 | October 14, 2018 18:06 |
[GAMBIT] How to plot S pipe | mariam.sara | ANSYS Meshing & Geometry | 36 | November 7, 2013 15:22 |
[ANSYS Meshing] is it possible to create virtual edges on the blades | er_ijaz | ANSYS Meshing & Geometry | 0 | November 3, 2013 05:15 |
[DesignModeler] Design Modeller create surface | papis | ANSYS Meshing & Geometry | 0 | October 31, 2013 13:52 |