Moved thread

elenaSh · September 11, 2012, 09:55

When I do mesh motion, nodes on boundary like WALL does not move. What can I do?

keon · September 11, 2012, 13:28

Hello,
I am a student from Malaysia, doing a research about calculating Trimaran resistance in calm water using ANSYS CFX , so, I want to know how I can get the resistance coefficient for the ship, detail of the setup is:

inlet; boundary details,subsonic, normal speed,22m/s, medium intensity-5%
outlet; boundary detail, subsonic, static pressure, 0 pa
wall; the hull itself, no slip wall
symmetry; the bottom, side and top of domain, set with free slip wall
domain; fluid domain,water,continuous solid,reference pressure=0 pa ,stationary
Global initialisation; domain initialisation, cartesian, automatic with value, U=22m/s,V=0m/s and W=0m/s, medium intensity-5%

I am new with ANSYS, and this setup is based from a basic tutorial I found in internet, if there is any error or suggestion, please feel free to tell me, below is the link for the image of my work...

ghorrocks · September 11, 2012, 20:19

I have moved this thread to a new thread. Please do not hijack other threads.

Mesh motion - do the tutorial examples in CFX on mesh motion.

Resistance - Use the force_x/y/z functions to get the force on the body and calculate resistance coefficient from there.

September 11, 2012, 09:55	Moved thread	#1
elenaSh New Member elena shaporenko Join Date: Aug 2012 Posts: 1 Rep Power: 0	When I do mesh motion, nodes on boundary like WALL does not move. What can I do?

September 11, 2012, 13:28	Resistant Coefficient (Ct)	#2
keon New Member khairun naim Join Date: Jul 2012 Posts: 3 Rep Power: 15	Hello, I am a student from Malaysia, doing a research about calculating Trimaran resistance in calm water using ANSYS CFX , so, I want to know how I can get the resistance coefficient for the ship, detail of the setup is: inlet; boundary details,subsonic, normal speed,22m/s, medium intensity-5% outlet; boundary detail, subsonic, static pressure, 0 pa wall; the hull itself, no slip wall symmetry; the bottom, side and top of domain, set with free slip wall domain; fluid domain,water,continuous solid,reference pressure=0 pa ,stationary Global initialisation; domain initialisation, cartesian, automatic with value, U=22m/s,V=0m/s and W=0m/s, medium intensity-5% I am new with ANSYS, and this setup is based from a basic tutorial I found in internet, if there is any error or suggestion, please feel free to tell me, below is the link for the image of my work...

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
udf problem	jane	Fluent UDF and Scheme Programming	37	February 20, 2018 05:17
Guide: Getting Started with the CFD Online Discussion Forums	pete	Site Help, Feedback & Discussions	8	July 29, 2016 06:00
Possible to loop a face thread inside a cell thread loop?	MarcusW	FLUENT	3	March 7, 2012 07:32
Please check out my parallelized udf code	aleisia	Fluent UDF and Scheme Programming	0	June 10, 2011 17:16
Phase locked average in run time	panara	OpenFOAM	2	February 20, 2008 15:37

September 11, 2012, 20:19		#3
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 18,017 Rep Power: 146	I have moved this thread to a new thread. Please do not hijack other threads. Mesh motion - do the tutorial examples in CFX on mesh motion. Resistance - Use the force_x/y/z functions to get the force on the body and calculate resistance coefficient from there.