Heat pipe

Saleh1970 · September 9, 2013, 00:31

Hi all,
recently, I got project to do simulation for it this project was using heat pipe as heat transfer tecniqe to enhace heat transfer between the heat transfer fluid and phase change materials.
my question is how 2 set the heat pipe with CFX

Like

ghorrocks · September 9, 2013, 01:03

Heat pipes are difficult to simulate due to the multiphase flow and condensation and vapourisation. This is not a flow for beginners and you are not going to find a tutorial on setting them up.

Saleh1970 · September 9, 2013, 01:23

I englect the advective effect of liquid return from the condenser to the evaporator. In addition, the resistances due to evaporation and condensation inside the heat pipes are assumed to be negligible

Saleh1970 · September 9, 2013, 01:36

Dear, All
Please if any body have any knowledge please help
with kind regards
Saleh

ghorrocks · September 9, 2013, 01:55

Can you post an image of what you are proposing to model, and the important physics.

Saleh1970 · September 9, 2013, 03:37

Thanks ghorrocks for your reply

I attached my geometry with this message. I'm using Therminol VP-1 as heat transfer fluid, Potassium nitrate as phase change material, steel for tube and heat pipe. The dimensions for heat pipes (Condenser length 0.140m, Evapporator length 0.100m, and Adiabatic length 0.060m). The tube dimensions (Tube outer radius 0.250m, Tube wall thickness 0.003m). The module length 0.120m. I'm following published paper for all these information

ghorrocks · September 9, 2013, 05:42

I have no idea what that image shows. Can you please explain what it is showing.

What are you trying learn with this simulation?

Saleh1970 · September 9, 2013, 06:59

Dear, ghorrocks
If possible please post your e-mail and I will send to you a paper I'm following and we will make deeply discussion about my case.
Regards
Saleh

ghorrocks · September 9, 2013, 07:31

I do not give my email on the forum. And don't PM me either, I do not answer CFD questions by PM.

Post it on the forum.

September 9, 2013, 00:31	Heat pipe	#1
Saleh1970 New Member Saleh Join Date: Apr 2013 Posts: 7 Rep Power: 13	Hi all, recently, I got project to do simulation for it this project was using heat pipe as heat transfer tecniqe to enhace heat transfer between the heat transfer fluid and phase change materials. my question is how 2 set the heat pipe with CFX Like

September 9, 2013, 01:23	Heat Pipe	#3
Saleh1970 New Member Saleh Join Date: Apr 2013 Posts: 7 Rep Power: 13	I englect the advective effect of liquid return from the condenser to the evaporator. In addition, the resistances due to evaporation and condensation inside the heat pipes are assumed to be negligible

September 9, 2013, 01:36	Heat Pipe	#4
Saleh1970 New Member Saleh Join Date: Apr 2013 Posts: 7 Rep Power: 13	Dear, All Please if any body have any knowledge please help with kind regards Saleh

September 9, 2013, 06:59	Heat Pipe	#8
Saleh1970 New Member Saleh Join Date: Apr 2013 Posts: 7 Rep Power: 13	Dear, ghorrocks If possible please post your e-mail and I will send to you a paper I'm following and we will make deeply discussion about my case. Regards Saleh

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how to analysis double pipe heat exchanger in cfx	rammax8	CFX	12	February 14, 2014 16:10
Enforce bounds error with heat loss boundary condition at solid walls	Chander	CFX	2	May 1, 2012 20:11
FEA Simulation of heat pipe	bensonnggl	ANSYS	0	September 25, 2010 00:59
Convective Heat Transfer - Heat Exchanger	Mark	CFX	6	November 15, 2004 15:55
heat transfer through fluids in a pipe in pipe	madasu	FLUENT	1	July 15, 2002 10:14

September 9, 2013, 01:03		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Heat pipes are difficult to simulate due to the multiphase flow and condensation and vapourisation. This is not a flow for beginners and you are not going to find a tutorial on setting them up.

September 9, 2013, 01:55		#5
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Can you post an image of what you are proposing to model, and the important physics.

September 9, 2013, 05:42		#7
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	I have no idea what that image shows. Can you please explain what it is showing. What are you trying learn with this simulation?

September 9, 2013, 07:31		#9
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	I do not give my email on the forum. And don't PM me either, I do not answer CFD questions by PM. Post it on the forum.