Results from parameter study

-mAx- · February 23, 2015, 02:03

Hello,
I computed one parameter study with stroke of piston as parameter.
All design points are done, and I want to observe the flowfield on a plane for each stroke.
If I load one result-set, I see the result "patched" on another grid, and the stroke of piston in't updated.
So I cannot post-process my parameter study.
Is there a workaround?
I am running 13.1 Version
Thanks a lot

Boris_M · March 2, 2015, 08:27

Hi Maxime,

If you define the plots you want to post process before running the parametric study, then you can select them as output information as well as goals and the images are created directly after each calculation.
If you haven't done this you cannot directly do any changes in the parametric study but you can export the design points as separate projects and use the compare feature to compare a plot you created in one project and get the same plot for all projects you select in the compare feature.

Boris

-mAx- · March 3, 2015, 08:27

Hello Boris,
Unfortunately I didn't get your last point.
I am quite lazy for computing all the design points again.

So I have one design point (project), and in this one I created my parameter study.
All my points are included in this parameter study and I am not able to call any of those points, except from "load data from", and I need then to choose one of the results included in the parameter study folder.
Unbenannt.jpg

Boris_M · March 3, 2015, 09:58

You can right click on the design point name in that table and use the create project. I think you can also use multi select and do that for all of them or so. I don't have the software open at the moment.

Boris

-mAx- · March 4, 2015, 04:18

yes, I got it now.
Thank you

February 23, 2015, 02:03	Results from parameter study	#1
-mAx- Super Moderator Maxime Perelli Join Date: Mar 2009 Location: Switzerland Posts: 3,297 Rep Power: 41	Hello, I computed one parameter study with stroke of piston as parameter. All design points are done, and I want to observe the flowfield on a plane for each stroke. If I load one result-set, I see the result "patched" on another grid, and the stroke of piston in't updated. So I cannot post-process my parameter study. Is there a workaround? I am running 13.1 Version Thanks a lot __________________ In memory of my friend Hervé: CFD engineer & freerider

March 3, 2015, 08:27		#3
-mAx- Super Moderator Maxime Perelli Join Date: Mar 2009 Location: Switzerland Posts: 3,297 Rep Power: 41	Hello Boris, Unfortunately I didn't get your last point. I am quite lazy for computing all the design points again. So I have one design point (project), and in this one I created my parameter study. All my points are included in this parameter study and I am not able to call any of those points, except from "load data from", and I need then to choose one of the results included in the parameter study folder. Unbenannt.jpg __________________ In memory of my friend Hervé: CFD engineer & freerider

March 3, 2015, 09:58		#4
Boris_M Disabled Join Date: Jul 2009 Posts: 616 Rep Power: 23	You can right click on the design point name in that table and use the create project. I think you can also use multi select and do that for all of them or so. I don't have the software open at the moment. Boris -mAx- likes this.

March 4, 2015, 04:18		#5
-mAx- Super Moderator Maxime Perelli Join Date: Mar 2009 Location: Switzerland Posts: 3,297 Rep Power: 41	yes, I got it now. Thank you __________________ In memory of my friend Hervé: CFD engineer & freerider

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problem: Very long "write" time (~2h-3h) for results and transient results	Shawn_A	CFX	16	April 12, 2016 20:49
Transient Run - Output "Time" in partial results?	evcelica	CFX	2	May 16, 2012 21:36
Lost Scenario Results..??	Fugacity	Autodesk Simulation CFD	1	February 24, 2012 10:48
Grid Refinement Study - How many cells necessary for accurate results?	ejvikings	FLUENT	1	January 22, 2012 00:33
compile errors of boundary condition "expDirectionMixed"	liying02ts	OpenFOAM Bugs	2	February 1, 2010 20:11

March 2, 2015, 08:27		#2
Boris_M Disabled Join Date: Jul 2009 Posts: 616 Rep Power: 23	Hi Maxime, If you define the plots you want to post process before running the parametric study, then you can select them as output information as well as goals and the images are created directly after each calculation. If you haven't done this you cannot directly do any changes in the parametric study but you can export the design points as separate projects and use the compare feature to compare a plot you created in one project and get the same plot for all projects you select in the compare feature. Boris