Missing Option on Display

Rajkool · March 10, 2020, 12:18

Hello everyone,

I cannot see the plot option in the mass flow rate in fluent 2019 R2. Is it something wrong in the settings of Fluent R2 or it is default? Because I can find it in R3.

Thanks in advance.

vinerm · March 11, 2020, 03:13

You may define the plot separately under Report Plot.

Rajkool · March 11, 2020, 06:22

Yeah, I have searched for it. I am attaching the pics of ansys 2019 19.2, as you can see there is no option.

Once you by mistakenly close the window, then we should simulate again for the results as there is no plot option.

Is this common or there is any settings?

vinerm · March 11, 2020, 06:30

The plot is already defined. The options are just extra. With newer versions, plot is a separate entity. As you observe that it is defined under Report Plots. So, it already is a plot.

Rajkool · March 11, 2020, 07:16

So, is there a way to regenerate the plot, once the window is closed by mistake after simulation?

vinerm · March 11, 2020, 07:33

If Fluent saved the data within data file, then you just need to run for 1 iteration and the plot will show. Usually, Fluent does not do that. Hence, if you did not write it out as an external file, plot is gone.

Rajkool · March 11, 2020, 09:11

Oh Okay. I'll try it.

Thank you Vinerm

Raj

March 11, 2020, 03:13	Plot	#2
vinerm Senior Member Vinerm Join Date: Jun 2009 Location: Nederland Posts: 2,946 Blog Entries: 1 Rep Power: 35	You may define the plot separately under Report Plot. __________________ Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority.

March 11, 2020, 06:30	Plot	#4
vinerm Senior Member Vinerm Join Date: Jun 2009 Location: Nederland Posts: 2,946 Blog Entries: 1 Rep Power: 35	The plot is already defined. The options are just extra. With newer versions, plot is a separate entity. As you observe that it is defined under Report Plots. So, it already is a plot. __________________ Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority.

March 11, 2020, 07:16	Option to regenerate closed window	#5
Rajkool Member Raj Join Date: Jan 2020 Posts: 92 Rep Power: 6	So, is there a way to regenerate the plot, once the window is closed by mistake after simulation?

March 11, 2020, 07:33	Plot after simulation	#6
vinerm Senior Member Vinerm Join Date: Jun 2009 Location: Nederland Posts: 2,946 Blog Entries: 1 Rep Power: 35	If Fluent saved the data within data file, then you just need to run for 1 iteration and the plot will show. Usually, Fluent does not do that. Hence, if you did not write it out as an external file, plot is gone. Rajkool likes this. __________________ Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Domain Reference Pressure and mass flow inlet boundary	AdidaKK	CFX	75	August 20, 2018 05:37
Difficulty in calculating angular velocity of Savonius turbine simulation	alfaruk	CFX	14	March 17, 2017 06:08
Wrong multiphase flow at rotating interface	Sanyo	CFX	14	February 7, 2017 17:19
Multiphase flow - incorrect velocity on inlet	Mike_Tom	CFX	6	September 29, 2016 01:27
Compression stoke is giving higher pressure than calculated	nickjuana	CFX	62	May 19, 2015 13:32

March 11, 2020, 09:11		#7
Rajkool Member Raj Join Date: Jan 2020 Posts: 92 Rep Power: 6	Oh Okay. I'll try it. Thank you Vinerm Raj