twoPhaseEulerFoam inlet velocity

jagan1mohan · June 13, 2020, 09:52

Hello Team, I'm looking to compare twoPhaseEulerFoam (2PEF) and CFDEM setup via simulating minimum fluidization velocity. In CFDEM setup, inlet velocity at the inlet boundary in the simulation is exactly same as we give in U dictionary. That is, I defluidize from 0.6 m/s to 0.0 m/s in 10 secs and functionObject confirms this.

In CFDEM, I use type flowRateInletVelocity; for gas.
In 2PEF, we have type interstitialInletVelocity; and it depends on alpha.air;

Value applied at inlet boundary is very different from one specified in U dictionary.

1. How do we maintain exact gas velocity in 2PEF?

Thank you,
Jagan Mohan.

Ardali · June 13, 2020, 11:46

As I understood, you want to specify time varying inlet velocity for air.
In this case, there are many ways to do so.
The easiest way is using

inlet
{
type uniformFixedValue;
uniformValue table ((0 (0 0.6 0)) (10 ( 0 0 0));
}
double check my syntax.
This boundary decreases the velocity in y-direction from 0.6 to 0 in 10 secs.
Hope it works.
You do not need to change alpha.air. keep the alpha value at inlet 1.
Ardalan

June 13, 2020, 09:52	twoPhaseEulerFoam inlet velocity	#1
jagan1mohan New Member Jagan Mohan Join Date: Dec 2019 Location: New York Posts: 26 Rep Power: 6	Hello Team, I'm looking to compare twoPhaseEulerFoam (2PEF) and CFDEM setup via simulating minimum fluidization velocity. In CFDEM setup, inlet velocity at the inlet boundary in the simulation is exactly same as we give in U dictionary. That is, I defluidize from 0.6 m/s to 0.0 m/s in 10 secs and functionObject confirms this. In CFDEM, I use type flowRateInletVelocity; for gas. In 2PEF, we have type interstitialInletVelocity; and it depends on alpha.air; Value applied at inlet boundary is very different from one specified in U dictionary. 1. How do we maintain exact gas velocity in 2PEF? Thank you, Jagan Mohan.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Pressure problems with inlet variable velocity	jaimesdiegop	CFX	2	September 1, 2016 03:31
3-D parabolic velocity Inlet - Steady state - UDF Turbulent Flow	mohibanwar	Fluent UDF and Scheme Programming	10	May 18, 2015 11:34
velocity inlet and ideal gas simultaneously-what's wrong?	preetam69	FLUENT	0	September 28, 2013 05:51
UDF problem : inlet velocity in cyl. coord. system	Jongdae Kim	FLUENT	0	June 15, 2004 12:21
what the result is negatif pressure at inlet	chong chee nan	FLUENT	0	December 29, 2001 06:13

June 13, 2020, 11:46		#2
Ardali Member Ardalan Join Date: Jul 2012 Location: Atlanta, USA Posts: 77 Rep Power: 14	As I understood, you want to specify time varying inlet velocity for air. In this case, there are many ways to do so. The easiest way is using inlet { type uniformFixedValue; uniformValue table ((0 (0 0.6 0)) (10 ( 0 0 0)); } double check my syntax. This boundary decreases the velocity in y-direction from 0.6 to 0 in 10 secs. Hope it works. You do not need to change alpha.air. keep the alpha value at inlet 1. Ardalan