|
[Sponsors] |
May 24, 2013, 10:40 |
How to Texture to a surface
|
#1 |
Member
Join Date: Sep 2010
Posts: 30
Rep Power: 15 |
Hi everyone,
I d like to texture a image to a surface. I ve seen that there is in filter menu a tool called texture Map to Surface. But i don't get how to use the png i have upload and how to apply to a surface. Anyone could help me ? Thanks in advance |
|
May 25, 2013, 12:47 |
|
#2 |
Retired Super Moderator
Bruno Santos
Join Date: Mar 2009
Location: Lisbon, Portugal
Posts: 10,975
Blog Entries: 45
Rep Power: 128 |
Greetings Voyage_gui,
Have you tried to follow the instructions from this page: http://paraview.org/Wiki/ParaView:Texture Best regards, Bruno
__________________
|
|
May 27, 2013, 04:31 |
|
#3 |
Member
Join Date: Sep 2010
Posts: 30
Rep Power: 15 |
Hi wyldckat,
Thanks for the link. I can't find from File tab any Load texture (version 3.98.0 64bit on Windows 8). I have tried to open my image "capture.png" then create a surface called "Surface_texture" then apply a filter callef texture to surface and select texture coordinates. But it doesn't seem to work. Guillaume |
|
May 27, 2013, 17:18 |
|
#4 |
Retired Super Moderator
Bruno Santos
Join Date: Mar 2009
Location: Lisbon, Portugal
Posts: 10,975
Blog Entries: 45
Rep Power: 128 |
Hi Guillaume,
Try to set things up as shown in the attached image. Notice the "Load" option next to the "Texture" line. Best regards, Bruno
__________________
|
|
May 28, 2013, 04:40 |
|
#5 |
Member
Join Date: Sep 2010
Posts: 30
Rep Power: 15 |
Hi wyldckat,
thanks a lot for the info. Unfortunately you don't have the same interface (cf image) and i can't find Load near Texture. I have just updated to version 4.0 RC1 and still have same interface as i had before. Best Guillaume |
|
May 28, 2013, 17:18 |
|
#6 |
Retired Super Moderator
Bruno Santos
Join Date: Mar 2009
Location: Lisbon, Portugal
Posts: 10,975
Blog Entries: 45
Rep Power: 128 |
Hi Guillaume,
Sorry, I was (still am ) in a hurry and only managed to post the image. A few directions:
Bruno
__________________
|
|
May 29, 2013, 03:24 |
|
#7 |
Member
Join Date: Sep 2010
Posts: 30
Rep Power: 15 |
Thanks a lot for the tip ! That is what was missing.
Best Guillaume |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How To Create Fowcs William Hawkings Surface in Fluent? | marinkobezu | FLUENT | 7 | October 25, 2018 10:51 |
[Gmsh] Error : Self intersecting surface mesh, computing intersections & Error : Impossible | velan | OpenFOAM Meshing & Mesh Conversion | 3 | October 22, 2015 11:05 |
Simulation of varying contact angles for a large droplet of water on a surface | cp703 | CFX | 5 | July 20, 2013 06:08 |
Comsol (4.3): convert parametric surface into block? | sgalaz | COMSOL | 0 | November 9, 2012 09:20 |
free convection heat transfer from a heated horizontal surface through a liquid to a thin cooled fin | Kaushik | FLUENT | 1 | May 8, 2000 06:47 |