|
[Sponsors] |
April 19, 2017, 13:02 |
Transparency Setting
|
#1 |
New Member
Join Date: Apr 2017
Posts: 7
Rep Power: 9 |
Dear All,
I am a beginner, who use now paraview for post-process. how can I define Transparency View in Paraview that maximal value is transparency, minimal value has color, for example -> see. upload File JPG I use opacity, it don't work ... thanks very much for your answer & support! Kind Regards, Yaakov |
|
April 19, 2017, 13:09 |
|
#2 |
Member
Joshua
Join Date: Dec 2016
Location: St. Louis, Missouri
Posts: 91
Rep Power: 9 |
yaakov,
Paraview allows you to change the transparency by clicking on the "Edit Color Bar" icon in the tool bar. This will extend options involving what color and transparency the user wants in the "Mapping Data" interactive image. Joshua |
|
April 19, 2017, 13:35 |
|
#3 |
New Member
Join Date: Apr 2017
Posts: 7
Rep Power: 9 |
Hi Joshua,
thanks very much for your answer! I try to define the color for max value (click color box). I can get here only white color not transparency... |
|
April 19, 2017, 14:23 |
|
#4 |
Member
Joshua
Join Date: Dec 2016
Location: St. Louis, Missouri
Posts: 91
Rep Power: 9 |
yaakov,
Can you upload a full image of the paraview GUI where your having the issue with the edit color bar section open? Also if there is a way to make it bigger then a thumbnail that would help. Thank you, Joshua |
|
April 20, 2017, 06:59 |
|
#5 |
New Member
Join Date: Apr 2017
Posts: 7
Rep Power: 9 |
I send now a full image JPG
I can only define white color in Paraview... Thanks a lot! Yaakov |
|
April 20, 2017, 09:00 |
|
#6 |
Member
Joshua
Join Date: Dec 2016
Location: St. Louis, Missouri
Posts: 91
Rep Power: 9 |
yaakov,
Using the Mapping Data interface in Color map editor will handle the transparency. Make sure that "Enable opacity mapping for surfaces" is checked. The image attached shows an example where my max values are transparent. Hope this helps, Joshua |
|
April 20, 2017, 09:29 |
|
#7 |
New Member
Join Date: Apr 2017
Posts: 7
Rep Power: 9 |
Hallo Joshua,
thanks very much! I have checked "Enable opacity mapping for surfaces"... see test results (neu JPG), but I can only get the values in the surface. I am sure that the displacement value are not zeros in the valume as I use dirichlet boundary to enforce zero values. Kind Regards, Yaakov Last edited by yaakov; April 20, 2017 at 10:38. |
|
April 20, 2017, 10:55 |
|
#8 |
Member
Joshua
Join Date: Dec 2016
Location: St. Louis, Missouri
Posts: 91
Rep Power: 9 |
yaakov,
You could use a Theshold filter so that you only display values on a certain range. Then use the transparency on the scalar bar after that. Best Regards, Joshua |
|
April 21, 2017, 06:40 |
|
#9 |
New Member
Join Date: Apr 2017
Posts: 7
Rep Power: 9 |
Hi Joshua,
I have tried, I can not use the Theshold filter. see neu2.jpg only slice/clip filter are available. Regards, Yaakov |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fluent Parallelization Problem After AC Power Dropped | pawl | Hardware | 5 | November 13, 2016 06:08 |
using chemkin | JMDag2004 | OpenFOAM Pre-Processing | 2 | March 8, 2016 22:38 |
[snappyHexMesh] determining displacement for added points | CFDnewbie147 | OpenFOAM Meshing & Mesh Conversion | 1 | October 22, 2013 09:53 |
Cells with t below lower limit | Purushothama | Siemens | 2 | May 31, 2010 21:58 |
Warning 097- | AB | Siemens | 6 | November 15, 2004 04:41 |