[ICEM] Some hints required on blocking geometry

air_engineer_arsenal · August 15, 2012, 02:06

Previously I learned about the blocking topology of swept wing from Far and no now I have to learn about the blocking of F6 Wing with fuselage. I now the same blocking topology will work fine for this case but I am confused how O-grid or C-grid will be inserted in this case. Some tips and advices required on how to insert C-grid and where to make splits in the C-grid for good blocking. I am attaching the .prj file with the post. Thanks in advance.

Regards

Far · August 15, 2012, 07:52

Quote:

Previously I learned about the blocking topology of swept wing from Far

In fact, original ideas are due to Simon.

Far · August 15, 2012, 07:56

Zip file only contains the .prj (project file). You need to attach the .tin file at least.

cfd seeker · August 15, 2012, 14:14

Quote:

Originally Posted by Far

Zip file only contains the .prj (project file). You need to attach the .tin file at least.

.tin size was of large size that's why I only attached .prj file but what's the point? If you open project file into ICEM it just behave like .tin file after opening so that you can make any changes to it isn't it?

siw · August 15, 2012, 15:15

If you go to the ANSYS Customer Portal there is a PDF file in the tutorials section for version 11, in it is a tutorial for blocking an aircraft similar to the F6. That might help you.

Far · August 15, 2012, 15:53

Quote:

Originally Posted by cfd seeker

.tin size was of large size that's why I only attached .prj file but what's the point? If you open project file into ICEM it just behave like .tin file after opening so that you can make any changes to it isn't it?

Are you air_engineer_arsenal

Admin plz don't allow double accounts from same IP

diamondx · August 16, 2012, 11:58

what is going on here !!!!!

August 16, 2012, 11:58		#7
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 29	what is going on here !!!!! __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[ICEM] Using Blocking with ICEM (infinite blocking lines appeared)	Touré	ANSYS Meshing & Geometry	2	August 5, 2012 17:27
[ICEM] Meshing adjacent wall geometry and simple ICEM questions	everdimension	ANSYS Meshing & Geometry	25	June 20, 2012 04:25
[ICEM] Best way to import geometry ICEM	Cottbus	ANSYS Meshing & Geometry	4	June 12, 2012 09:42
[ICEM] Cylinder Geometry and Blocking	Leepox	ANSYS Meshing & Geometry	2	November 21, 2011 10:32
paraFoam reader for OpenFOAM 1.6	smart	OpenFOAM Installation	13	November 16, 2009 21:41

August 15, 2012, 07:56		#3
Far Senior Member Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,560 Blog Entries: 6 Rep Power: 55	Zip file only contains the .prj (project file). You need to attach the .tin file at least.

August 15, 2012, 15:15		#5
siw Senior Member Stuart Join Date: Jul 2009 Location: Portsmouth, England Posts: 746 Rep Power: 26	If you go to the ANSYS Customer Portal there is a PDF file in the tutorials section for version 11, in it is a tutorial for blocking an aircraft similar to the F6. That might help you.