|
[Sponsors] |
Error: zone-surface: invalid thread[2] Error Object: #f |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
December 13, 2015, 13:38 |
Error: zone-surface: invalid thread[2] Error Object: #f
|
#1 |
Member
Reslan Technical
Join Date: Nov 2015
Posts: 49
Rep Power: 10 |
hi
Error: zone-surface: invalid thread[2] Error Object: #f what is means |
|
April 3, 2017, 03:11 |
|
#2 |
New Member
Shirlin
Join Date: Sep 2016
Location: India
Posts: 5
Rep Power: 9 |
hi
i am getting a similar error Error: zone-surface: invalid thread[2] could someone tell how to solve . |
|
April 3, 2017, 03:17 |
|
#3 |
Senior Member
Paritosh Vasava
Join Date: Oct 2012
Location: Lappeenranta, Finland
Posts: 732
Rep Power: 22 |
It is bit tricky to answer with such small amount of details available.
Anyways, first thing you must do it check the monitors setup. It is possible that the surface or volume for the monitor has been renamed or deleted. |
|
April 3, 2017, 05:42 |
|
#4 |
New Member
Shirlin
Join Date: Sep 2016
Location: India
Posts: 5
Rep Power: 9 |
Thank u for the response,,i am getting the error even before the monitors have been set.the error is due to some problem in meshing, i have used face split to mesh the domain
|
|
June 30, 2018, 06:56 |
|
#5 | |
Member
Anomymous
Join Date: May 2018
Posts: 31
Rep Power: 7 |
Quote:
I am also facing this problem but could not able to solve it by re-meshing, can you please suggest how to do it. Thank you |
||
November 1, 2018, 19:40 |
Invalid Thread -Fluent 14-
|
#6 |
New Member
Amin
Join Date: Oct 2018
Posts: 2
Rep Power: 0 |
Hi guys,
I faced the same error when exporting the mesh to the solver. I figured out that the problem resided on some faces I named improperly after I've done the mesh (in the aim to define boundary conditions by after). Obviously, the parts' names should not interfere. I hope it will help ) |
|
December 26, 2020, 00:09 |
|
#7 |
New Member
binhminhdanh2
Join Date: Dec 2020
Posts: 1
Rep Power: 0 |
why dont gain it?
i can and i throw one's weight around be in control manifest knuckle under LSA Activity Value – Review |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[snappyHexMesh] SnappyHexMesh no layers and no decent mesh for complex geometry | pizzaspinate | OpenFOAM Meshing & Mesh Conversion | 1 | February 25, 2015 07:05 |
[snappyHexMesh] Problem with Sanpper, surface still Rough | Zephiro88 | OpenFOAM Meshing & Mesh Conversion | 7 | November 5, 2014 12:05 |
Comsol (4.3): convert parametric surface into block? | sgalaz | COMSOL | 0 | November 9, 2012 09:20 |
Normal - Helical Surface | m. malik | Main CFD Forum | 3 | February 3, 2006 12:56 |
solid edge problem....can you help? | cindy | Main CFD Forum | 3 | April 5, 2004 13:43 |