Forum: Main CFD Forum
July 23, 2019, 15:38
|
Replies: 0
Views: 561
High Pressure Steam release to atmosphere
This might be a very trivial question.
I have been trying to figure out but did not succeed due to lack of my background. It will be very helpful, if someone can explain
If high pressure steam...
|
Forum: OpenFOAM Running, Solving & CFD
October 29, 2017, 06:58
|
Replies: 2
Views: 1,472
|
Forum: OpenFOAM Running, Solving & CFD
October 25, 2017, 23:44
|
Replies: 2
Views: 1,472
How to model release of steam to the atmosphere!
Dear All,
I want to solve the problem of steam release to the atmosphere from a pressure relief valve. The release is expected at a height (~30m from ground) in vertically upward direction.
The...
|
Forum: OpenFOAM
July 5, 2017, 21:43
|
Replies: 3
Views: 2,349
|
Forum: OpenFOAM Running, Solving & CFD
March 31, 2017, 03:33
|
Replies: 13
Views: 3,079
|
Forum: OpenFOAM Running, Solving & CFD
March 31, 2017, 03:10
|
Replies: 13
Views: 3,079
|
Forum: OpenFOAM Running, Solving & CFD
March 31, 2017, 02:57
|
Replies: 13
Views: 3,079
|
Forum: OpenFOAM Running, Solving & CFD
March 31, 2017, 02:41
|
Replies: 13
Views: 3,079
|
Forum: OpenFOAM Running, Solving & CFD
March 31, 2017, 01:44
|
Replies: 13
Views: 3,079
|
Forum: OpenFOAM Running, Solving & CFD
December 14, 2016, 00:41
|
Replies: 1
Views: 905
|
Forum: Main CFD Forum
December 1, 2016, 23:03
|
Replies: 0
Views: 1,032
High inlet Turbulence vs Low inlet Turbulence
Hi everyone,
I am simulating steady state flow around a set of buildings using k epsilon model.
The problem I am facing is that, if I set higher values of inlet turbulence (40%), I get a well...
|
Forum: OpenFOAM Running, Solving & CFD
October 19, 2016, 10:11
|
Replies: 4
Views: 1,704
Hi, y_jiang...
Its an old thread, but I hope I...
Hi, y_jiang...
Its an old thread, but I hope I can get a reply from you for how you actually solved your problem, and
I am also working on scalarTransportFoam, and I want to include a sink to it,...
|
Forum: OpenFOAM Programming & Development
September 20, 2016, 06:40
|
Replies: 0
Views: 1,031
Using fvOptions for pollutant sink
Hi everyone,
I have a problem in hand involving transport of a pollutant (concentration) in a given velocity field. I am using scalarTransportFoam for this purpose on a pre-calculated velocity...
|
Forum: Main CFD Forum
August 31, 2016, 05:30
|
Replies: 1
Views: 910
|
Forum: OpenFOAM Running, Solving & CFD
August 21, 2016, 09:01
|
Replies: 1
Views: 944
|
Forum: OpenFOAM Running, Solving & CFD
August 20, 2016, 10:01
|
Replies: 1
Views: 944
How to add a Sink for Passive Scalar
Hi everyone,
I am trying to simulate transport of a gas (passive scalar) in a flow field (air) using scalarTransportFoam. One of the patches acts as a suction, where gas should be collected. Which...
|
Forum: OpenFOAM Running, Solving & CFD
March 14, 2016, 18:59
|
Replies: 3
Views: 1,041
|
Forum: OpenFOAM Running, Solving & CFD
March 14, 2016, 12:36
|
Replies: 3
Views: 1,041
|
Forum: OpenFOAM Running, Solving & CFD
March 13, 2016, 00:11
|
Replies: 3
Views: 1,041
|
Forum: OpenFOAM Running, Solving & CFD
March 12, 2016, 13:31
|
Replies: 3
Views: 1,041
fixedValue Outlet
Hi everyone,
I have an experimental setup inside a closed chamber. The air is injected to the chamber through nozels. There are four exhaust holes for venting chamber using a fan. Velocity...
|
Forum: OpenFOAM Running, Solving & CFD
December 17, 2015, 15:21
|
Replies: 0
Views: 1,564
Initialization using PotentialFoam
Hi guys!
Usually it is recommended to initialize U and P using PotentialFoam,
Is this recommended for flows involving multiple inlets inside domain?
I observed that while I initialized this kind...
|
Forum: OpenFOAM Running, Solving & CFD
December 11, 2015, 10:03
|
Replies: 2
Views: 948
Thank you sergiu tofanel for the interest.
The...
Thank you sergiu tofanel for the interest.
The problem is not of the convergence, my solution is converged and all the forces and the coefficients are stable.
The problem is with the negative Cd...
|
Forum: OpenFOAM Running, Solving & CFD
December 11, 2015, 00:06
|
Replies: 2
Views: 948
Anomoly in Drag Coefficent
Hi
I am simulating air flow around a building (dome like) using OpenFoam (Re ~10^7).
The problem is with the drag coefficent.
The drag coefficent calculated while using upwind scheme for...
|
Forum: Main CFD Forum
September 22, 2015, 04:25
|
Replies: 4
Views: 1,254
Thanks For Your Interest D.B!
I have shared...
Thanks For Your Interest D.B!
I have shared domain image with my 1st post, but I think it was not visible (My bad), however, I am sharing it again.
The ultimate aim is to contain and collect...
|
Forum: Main CFD Forum
September 21, 2015, 06:29
|
Replies: 4
Views: 1,254
|