Mesh: faces with no faces

MarcelloAsciolla · April 21, 2018, 15:24

I got this error passing a model from the "geometry" block to the "mesh" one.

"A body was processed that had faces with no facets. Mesh generation and mass property calculations may be impacted".

But I am not understanding it.

Are not the facets created from the faces, so after the creation of the mesh?

I mean that I expect this kind of error after the creation of the mesh, why do I get it when I am importing a geometry in the mesh section so before the creation itself?
What does this refer exactly?

alinik · February 25, 2019, 10:53

did you have any luck finding out what was the problem?

MarcelloAsciolla · March 1, 2019, 10:53

There was something wrong in the CAD model. I did a little simplification and everything worked fine.

AidealZohary · November 30, 2019, 06:33

Just for those who're still searching. I had the same problem with my Cad where i designed a wing with a rounded tip using loft in solidworks. I changed the approach by using surfacing and later used surface knit to change it into solid and now it works well.

April 21, 2018, 15:24	Mesh: faces with no faces	#1
MarcelloAsciolla Member Marcello Asciolla Join Date: Apr 2018 Location: Italy Posts: 43 Rep Power: 8	I got this error passing a model from the "geometry" block to the "mesh" one. "A body was processed that had faces with no facets. Mesh generation and mass property calculations may be impacted". But I am not understanding it. Are not the facets created from the faces, so after the creation of the mesh? I mean that I expect this kind of error after the creation of the mesh, why do I get it when I am importing a geometry in the mesh section so before the creation itself? What does this refer exactly?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] Can't Shake Erros: patch type 'patch' not constraint type 'empty'	BrendaEM	OpenFOAM Meshing & Mesh Conversion	12	April 3, 2022 19:32
[Other] Mesh Importing Problem	cuteapathy	ANSYS Meshing & Geometry	2	June 24, 2017 06:29
[snappyHexMesh] SHM is not extruding/adding Layers everywhere	matthiasd	OpenFOAM Meshing & Mesh Conversion	2	October 16, 2016 17:45
[ICEM] Export ICEM mesh to Gambit / Fluent	romekr	ANSYS Meshing & Geometry	1	November 26, 2011 13:11
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 12:55

February 25, 2019, 10:53		#2
alinik Senior Member ali Join Date: Oct 2009 Posts: 318 Rep Power: 18	did you have any luck finding out what was the problem?

March 1, 2019, 10:53		#3
MarcelloAsciolla Member Marcello Asciolla Join Date: Apr 2018 Location: Italy Posts: 43 Rep Power: 8	There was something wrong in the CAD model. I did a little simplification and everything worked fine.

November 30, 2019, 06:33		#4
AidealZohary New Member Aideal Zohary Join Date: Feb 2019 Location: Malaysia Posts: 28 Rep Power: 8	Just for those who're still searching. I had the same problem with my Cad where i designed a wing with a rounded tip using loft in solidworks. I changed the approach by using surfacing and later used surface knit to change it into solid and now it works well.