OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	June 21, 2024 07:54 by Martin_Sz	26	55,062
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	March 25, 2023 08:50 by ancolli	19	70,248
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	September 2, 2021 06:29 by hakosaj	10	22,995
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 16:54 by rdbisme	17	21,840
Sticky: How to give enough info to get help linnemann	September 20, 2017 10:19 by linnemann	8	58,595
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 08:34 by wyldckat	178	71,851
Problem with InterFoam. miroder	November 5, 2009 19:06 by miroder	4	2,839
nonuniform boundary condition( U=f(y) ) ? panda60	November 5, 2009 13:28 by ICL	2	1,961
hybrid rocket combustion? PattiMichelle	November 5, 2009 12:33 by PattiMichelle	0	3,445
Heat Transfer ( 1 2) ronaldo	November 5, 2009 12:20 by LarsPT	34	6,932
CYCLIC BC in pipe flows matthias	November 5, 2009 11:52 by matthias	0	4,139
calculation of gradients near wall crazysumi	November 5, 2009 09:54 by crazysumi	1	1,937
gas(same density with air) dispersion in the air ? panda60	November 5, 2009 06:42 by panda60	0	1,677
High pressure in rhopSonicFoam results in negative pressure shangzung	November 5, 2009 04:24 by shangzung	0	2,362
Problem with Paraview graphics Ronnfors	November 4, 2009 13:49 by franzisko	8	3,994
problem when use foamToVTK ouafa	November 4, 2009 12:57 by ouafa	6	3,028
parallel results different depending on decomposition strategy franzisko	November 4, 2009 07:37 by franzisko	3	2,297
Openfoam 1.6 ar_mofidi	November 4, 2009 06:26 by dfransos	1	2,534
Advice for wind problem? griztown	November 3, 2009 18:43 by griztown	3	1,694
Get direct access to a particle gruber	November 3, 2009 06:26 by gruber	3	1,945
About the use of software FOAM Li Yang	November 2, 2009 23:59 by ollickle	9	2,394
who can develop a process to convert radiatn	November 2, 2009 20:38 by radiatn	0	1,450
no parallel computing using "dynamicBodyFvMesh" Bastian	November 2, 2009 20:06 by Bastian	13	2,846
Boundary conditions for reflecting wall and hole shangzung	November 2, 2009 15:50 by shangzung	0	1,696
Cyclic Boundary Condition/Periodic boundary deji	November 2, 2009 13:53 by deji	0	1,640
settlingFoam error in openFoam 1.6.x pramodopen4foam	November 2, 2009 08:04 by pramodopen4foam	3	1,542
openFoam for fire dynamic simulation hadi1982	November 2, 2009 06:30 by elvis	2	5,800
Heat transfer in a Muffler vitor	November 2, 2009 05:48 by askjak	1	1,699
Tutorial problem: "rhopSonicFoam - shockTube" with high pressure shangzung	November 1, 2009 14:07 by shangzung	0	1,792
Breaking/shattering glass or other materials. Michel_sharp	October 31, 2009 21:03 by alberto	7	2,682
Setting up: Cube, 2 holes, high pressure inside shangzung	October 30, 2009 12:27 by shangzung	0	1,819
Can't simulate pressures over 80 bar in sonicFoam shangzung	October 30, 2009 11:21 by cnsidero	6	2,845
Confused with wall boundaries in 3D shangzung	October 30, 2009 05:49 by shangzung	2	1,591
Solver to study heat flux askjak	October 29, 2009 18:21 by askjak	0	1,605
boundary conditions for explosion in a tube shangzung	October 29, 2009 14:06 by bhh	1	1,578
FoamX for OpenFOAM 1.6 vitor	October 29, 2009 07:24 by sanjibdsharma	4	5,766
Residuals in the log file jml	October 29, 2009 07:05 by jml	0	1,775
trouble with totalTemperature BC pg22	October 29, 2009 06:49 by pg22	7	4,455
Load balancing pre- and during computation madad2005	October 29, 2009 06:23 by madad2005	1	1,721
OpenFOAM basic Question a_yoshi	October 29, 2009 05:13 by dmoroian	1	1,975
Choosing the right timestep shangzung	October 29, 2009 03:58 by shangzung	2	2,183
how to make parallel running? decomposePar. panda60	October 29, 2009 03:43 by chbenz	1	3,182
Basic Question a_yoshi	October 29, 2009 01:45 by a_yoshi	2	1,909
Internal Region ternik	October 28, 2009 15:56 by ternik	2	1,695
Cube in cube with blockMeshDict shangzung	October 28, 2009 09:45 by ternik	3	1,723
Can I simulate the internal combustion engine with OF? fuvictor	October 27, 2009 22:40 by fuvictor	0	2,210

Read this first: How to ask a question on the forums

Page 226 of 245

226

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 02:39.