OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	June 21, 2024 06:54 by Martin_Sz	26	53,700
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	March 25, 2023 07:50 by ancolli	19	66,191
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	September 2, 2021 05:29 by hakosaj	10	22,426
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 15:54 by rdbisme	17	21,396
Sticky: How to give enough info to get help linnemann	September 20, 2017 09:19 by linnemann	8	57,584
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 07:34 by wyldckat	178	70,339
forced convection on a cylinder mountaineer	September 27, 2011 10:30 by mountaineer	3	2,589
OpenFOAM validation mountaineer	September 27, 2011 09:10 by camoesas	10	3,430
Problem with pos() or Scalar.H seboxx	September 27, 2011 05:36 by seboxx	6	4,100
How to define Boundary Conditions in heat Transfer ?? almir	September 27, 2011 02:20 by Bernhard	3	2,272
open channel flow with open foam windyday	September 26, 2011 17:04 by windyday	4	3,614
Modeling intake and exhaust in ICE Alexvader	September 26, 2011 13:50 by Alexvader	2	2,787
chtMultiRegionSimpleFoam javad814	September 26, 2011 13:30 by mirko	1	3,890
pyrolysis in fireFoam windwin	September 26, 2011 08:11 by x056kuf	1	5,251
Gauss Quadrature points dhruv	September 26, 2011 04:59 by dhruv	4	3,646
how to increase maximum number iterations to > 1000? phsieh2005	September 25, 2011 17:02 by dimyriy	6	4,440
Problem in path of compiled FOAM utilities Alexvader	September 25, 2011 14:49 by Alexvader	4	1,678
How to create Prism Layer in OpenFOAM? j-avdeev	September 25, 2011 05:43 by jango	5	4,198
How to create cyclic boundary(fan B.C.) in openFOAM200. asamit	September 24, 2011 20:42 by asamit	14	3,625
Sgimpi ( 1 2) pere	September 24, 2011 07:57 by wyldckat	27	11,944
Errors building Openfoam 2.0.0 with icc and SGI mpt-2.03 jans	September 24, 2011 07:56 by wyldckat	6	4,609
ParaView/PV3Readers Compile Issue gankoji	September 24, 2011 07:25 by wyldckat	1	2,228
simulate a gas turbine combustor with dieselFoam kikko	September 23, 2011 20:32 by kikko	0	1,624
solar radiation javad814	September 23, 2011 16:43 by javad814	0	2,042
Bubble-column simulation using bubbleFoam voingiappone	September 22, 2011 16:23 by miles_davis	6	2,852
Problems to implement a coordinate change mateusps	September 22, 2011 13:20 by tomislav_maric	3	1,742
nu in cavity example MaaadBob	September 22, 2011 08:05 by MaaadBob	3	1,540
2D axisymmetric Mesh problem in OpenFoam Javed	September 22, 2011 02:23 by Hisham	3	5,950
Jet in free air vishal.indomitable	September 21, 2011 15:07 by kmooney	1	2,054
Viewing multiregion results mirko	September 21, 2011 06:02 by sparbroetchen	3	1,801
icoFoam continuity error tellico	September 21, 2011 03:43 by dhruv	1	1,930
How to create a free surface application in Openfoam ? ( 1 2) phuchuynh	September 21, 2011 03:35 by phuchuynh	28	11,329
CFD simulation of the wind over a terrain samiam1000	September 21, 2011 03:16 by samiam1000	0	1,736
extrudeMesh - odd behaviour grjmell	September 20, 2011 08:41 by grjmell	0	1,843
alternative method for ggi wWieWalter	September 20, 2011 08:18 by gschaider	1	1,995
Dsmc chitharenjan	September 20, 2011 04:11 by anon_a	1	3,210
how can I Run axisymmetric flow using dsmcFoam ? mechy	September 19, 2011 10:25 by anon_a	4	3,260
initial solution for a two phase simulation miles_davis	September 19, 2011 09:40 by miles_davis	0	1,253
Problem editing files when running in parallel Ladnam	September 19, 2011 03:35 by Ladnam	2	1,518
Running equations with different time steps inside a solver Tarak	September 18, 2011 22:06 by marupio	1	1,741
engineFoam variable definitions Alexvader	September 17, 2011 17:34 by Alexvader	0	1,642
chtMultiRegionSimpleFoam javad814	September 17, 2011 15:38 by nimasam	3	2,016
Paraview's Problem MOHAMMAD67	September 17, 2011 09:07 by wyldckat	3	1,994
Linking PETSc with OpenFoam Argen	September 16, 2011 16:36 by Argen	16	4,685
High aspect ratio oort	September 16, 2011 14:06 by oort	5	11,931
Preferances on OpenFOAM pre/postprocessing Software? ericnutsch	September 16, 2011 05:38 by thejaraju	10	3,574

Read this first: How to ask a question on the forums

Page 159 of 243

159

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 05:18.