OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	June 21, 2024 07:54 by Martin_Sz	26	53,075
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	March 25, 2023 08:50 by ancolli	19	64,323
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	September 2, 2021 06:29 by hakosaj	10	22,183
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 16:54 by rdbisme	17	21,189
Sticky: How to give enough info to get help linnemann	September 20, 2017 10:19 by linnemann	8	57,016
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 08:34 by wyldckat	178	69,587
Multiphase flow injected inisde MRF zone granzer	February 9, 2022 07:35 by granzer	1	659
Cell determinant (wellposedness) Zowie	February 8, 2022 12:51 by ghastbug	6	7,463
Error with BuoyantPimpleFoam Jojell	February 8, 2022 04:34 by Yann	1	971
dsmcFoam: Particle initialised with a location outside of the mesh. mely	February 5, 2022 14:19 by mely	0	1,131
Error Illegal dictionary entry or environment variable name gotterstab	February 4, 2022 10:41 by gotterstab	0	1,412
DecomposeParDict with weightField mortezahdr	February 3, 2022 11:10 by uosilos	1	1,427
GroovyBC warning MFWilliams	February 3, 2022 07:08 by MFWilliams	0	729
Sliding Body mrozki	February 2, 2022 11:37 by mrozki	0	683
Volume sampling on the run Ryan.	February 2, 2022 10:21 by lukasf	6	1,706
Data not written to folders Hr_kules	February 2, 2022 05:54 by Hr_kules	2	848
How to calculate the cumulative mass flow over time at patches (total mass volume)? jianglong	February 1, 2022 18:13 by Tobi	1	1,076
Question regarding force coefficient night-hawk	February 1, 2022 18:01 by Tobi	1	546
Help with FOAM fatal error (fault lying in snappyhexmesh) alexc1	February 1, 2022 11:01 by alexc1	0	638
triangular pipe flow problem Quest.Qiu	February 1, 2022 02:49 by al.csc	4	1,167
Modelling propeller slipstream with actuator disk cosmictrex	January 31, 2022 05:30 by Sachin m	6	1,653
mesh errors in Propellor example using checkMesh Maarten	January 29, 2022 05:34 by Maarten	0	579
SedFoam installation Ankur Kaushik	January 26, 2022 10:32 by eduard.puig.montella	2	1,001
how to achieve homogeneous vertical profile for turbulence saugatshr4	January 24, 2022 05:44 by mAlletto	9	1,662
Following Tutorial but it's not working sknill	January 20, 2022 12:00 by sknill	0	660
GroovyBC time varying lookup table MFWilliams	January 20, 2022 11:30 by MFWilliams	0	945
XiDyMFoam, Ignition error cunconbkhp	January 19, 2022 02:16 by ayushi	1	1,502
sphereDrop example not working cpadam	January 18, 2022 12:55 by Yann	3	792
OpenFOAMv7 WAVE Generation Problem zyfsoton	January 18, 2022 11:12 by zyfsoton	0	822
How to refine a surface when you have to mesh on both sides of the surface engg_student	January 18, 2022 08:59 by Tobi	1	959
alpha.water boundary condition wjchoi	January 18, 2022 08:55 by Tobi	1	1,517
Combustion hangs after a while - XiFoam casseer15	January 18, 2022 00:25 by casseer15	0	675
DensityBasedTurbo installation broken. Project dead? edwardsaid	January 17, 2022 22:56 by edwardsaid	0	610
Mutli region meshing, where are the patches stored? engg_student	January 17, 2022 05:30 by engg_student	2	918
2D vertical axis wind turbine, OpenFOAM beginner ( 1 2) Boloar	January 17, 2022 05:14 by linnemann	30	13,621
Implementing Spalart-Allmar model with QCR in Openfoam Crigerfra	January 16, 2022 23:08 by lpz456	1	1,076
Using codeStream with fvSchemes? jnanabrao	January 14, 2022 23:29 by jnanabrao	2	849
Is it reasonable to use gradient limiter on pressure gradient? xpqiu	January 14, 2022 12:40 by Tobi	2	1,972
Point is not inside mesh engg_student	January 14, 2022 12:32 by Tobi	1	978
Scaling of parallel computation? Solver/thread count combinations? tdof	January 13, 2022 12:39 by tdof	8	2,554
Mathematical representation of fixedDisplacementZeroShear boundary condition Sargam05	January 11, 2022 07:55 by bigphil	14	3,155
fixedGradient, zeroGradient? smillion	January 8, 2022 09:17 by Crane_	16	37,502
Printing interface area saicharan662000@gmail.com	January 7, 2022 06:12 by saicharan662000@gmail.com	1	811
How to acess the variable nHatf_ from interface properties and print it? saicharan662000@gmail.com	January 7, 2022 00:06 by saicharan662000@gmail.com	0	1
Where PLIC stores the area of Interface in openfoam? saicharan662000@gmail.com	January 7, 2022 00:00 by saicharan662000@gmail.com	1	874
Difference between OF fluent axisymmetric shocks!? baratian	January 5, 2022 05:50 by baratian	0	681

Read this first: How to ask a question on the forums

Page 26 of 242

« First

126

Last »

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 23:03.