OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	March 25, 2023 07:50 by ancolli	19	59,142
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	August 14, 2022 13:55 by mikethe1wheelnut	25	50,600
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	September 2, 2021 05:29 by hakosaj	10	21,722
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 15:54 by rdbisme	17	20,471
Sticky: How to give enough info to get help linnemann	September 20, 2017 09:19 by linnemann	8	55,203
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 07:34 by wyldckat	178	67,380
Solvers for reacting flows megacrout	March 15, 2013 05:35 by shijin	4	4,751
2D simulation of round jets hz283	March 15, 2013 04:55 by Bernhard	1	1,463
Negative absolute pressure in rhoPorousMRFSimpleFoam ( 1 2) doubtsincfd	March 15, 2013 04:42 by immortality	28	4,716
Conjugate heat transfer for natural convection Ank	March 15, 2013 00:06 by Ank	0	1,256
adding layer in dynamic mesh. Vadims.geza	March 14, 2013 13:44 by mturcios777	1	1,285
Derived Boundary condition mmkr825	March 14, 2013 07:50 by mmkr825	0	1,032
Article release about heat transfer analysis with OpenFOAM luca	March 14, 2013 02:32 by Sunxing	7	6,464
interpolated field at iso-surface 0.5 Andrea_85	March 13, 2013 18:58 by gschaider	3	2,631
Creat a Patch with zero size sasanghomi	March 13, 2013 15:59 by sasanghomi	6	1,788
Missing Output of debugwitch kflora	March 13, 2013 11:33 by kflora	0	1,837
Power Function hawkeye321	March 13, 2013 04:32 by cutter	1	1,807
Implementing an Equation Yahoo	March 12, 2013 12:08 by chegdan	5	1,723
Where is the attach/Detach face? sasanghomi	March 12, 2013 11:48 by mturcios777	2	1,516
Temperature Issue in OpenFOAM-2.2.0 prasant	March 12, 2013 07:17 by prasant	0	1,461
Running bubbleFoam for turbulent case... vishal3	March 12, 2013 06:13 by vishal3	7	1,758
fvc::div(phi,rho) vs fvc::div(phi) nimasam	March 12, 2013 03:59 by woodwick	13	12,009
Buckley-Leverett Problem CFDtoy	March 12, 2013 02:27 by Lalit	6	2,044
steady laminar incompressible non-premixed combustion shijin	March 12, 2013 00:31 by shijin	0	1,376
Numerical schemes for grad and div Tobi	March 11, 2013 21:24 by dkokron	6	3,540
Momentum predictor Andrea_85	March 11, 2013 04:09 by giack	6	12,389
lower velocity within the vicosity layer in a 2D LES case Sunxing	March 11, 2013 00:50 by Sunxing	0	893
valveDetachCyl &valveDetachPort in the boundary file sasanghomi	March 9, 2013 19:28 by sasanghomi	0	936
Arbitrary Meshing Interface rhee	March 9, 2013 18:14 by hz283	1	2,339
pressureInletVelocity deji	March 9, 2013 16:10 by deji	0	1,618
y+ values calculation in OpenFoam andrei.cimpoeru	March 8, 2013 05:39 by andrei.cimpoeru	4	5,560
1 Inlet 2 Outlet BC setup problem vbchris	March 8, 2013 01:38 by niklas	1	1,859
The FOAM Documentation Project - SHUT-DOWN ( 1 2 3 ... Last Page) holger_marschall	March 7, 2013 12:30 by holger_marschall	242	62,786
buoyantPressure Antonio.vucci	March 7, 2013 08:27 by giack	6	4,257
Help on heatTransfer problems Grimoli	March 6, 2013 17:00 by Grimoli	0	1,120
Initial residuals do not decrease... Igor_2011	March 6, 2013 13:07 by Yahoo	2	2,223
InterFoam vs InterDyMFoam Rose2011	March 6, 2013 10:56 by smraniaki	4	11,775
How to calculate cp, cv and gamma for compressible flow mecbe2002	March 6, 2013 05:34 by mecbe2002	0	2,164
Did you ever simulate a detonation with OpenFOAM? shangzung	March 6, 2013 04:06 by CharlieTan84	3	3,381
Explosion inside a cube - blockMesh shangzung	March 6, 2013 03:59 by CharlieTan84	3	2,639
Questions about simplefoam maoyanren	March 6, 2013 02:16 by anishtain4	1	1,269
Error while trying to read volVectorField blackbirdinapie	March 5, 2013 10:11 by Hisham	17	3,713
Modelling a Wind Farm in OpenFOAM BigLearner	March 5, 2013 03:25 by JoCo618	13	6,618
About the non-orthogonal mesh and non-orthogonal corrector lg88	March 5, 2013 03:11 by fredo490	8	7,200
High nuSGS value in periodic hill case turbfoam	March 4, 2013 18:42 by turbfoam	0	1,557
How to separate the porous region? hesamgh	March 4, 2013 17:58 by wyldckat	1	1,633

Read this first: How to ask a question on the forums

Page 119 of 239

119

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 03:04.