OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	May 12, 2020 11:34 by Tobermory	12	26,244
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	October 2, 2019 22:35 by rubens	24	35,888
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 16:54 by rdbisme	17	12,768
Sticky: How to give enough info to get help linnemann	September 20, 2017 10:19 by linnemann	8	39,055
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	March 30, 2017 06:19 by Samwise	9	14,143
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 08:34 by wyldckat	178	52,733
Internal faces JUST for post-processing purposes spitchers	February 3, 2017 09:21 by khedar	1	436
about fvSchemes with tetramesh bye bye my blue	February 2, 2017 21:29 by bye bye my blue	0	419
error in pimpleDyMFoam bye bye my blue	February 2, 2017 11:34 by khedar	2	775
paper request for lien cubic low Re and lien leschziner low re turbulence model romant	February 2, 2017 10:52 by Outbound	4	3,826
Lower calculation in parallel than in serial FlyingCat	February 1, 2017 22:07 by khedar	2	430
Tracking position of maximum vorticity Pascal_doran	February 1, 2017 19:09 by reza_65	15	2,969
Time step size sensitivity of piso algorithm TypeR	February 1, 2017 17:00 by Tobi	1	625
Sinusoidal motion airfoil pimpleDynamicFoam denis.sanga@hotmail.it	February 1, 2017 09:17 by denis.sanga@hotmail.it	0	536
OpenFOAM 1.7 cylindricalInletVelocity and swirlFlowRateInletVelocity BC's ALC	February 1, 2017 05:11 by pilafa	6	4,507
circuit board cooling ? liloM	February 1, 2017 03:17 by Tobi	9	2,525
make/files hrhm_04	January 31, 2017 11:20 by hrhm_04	4	587
How to use and compile comfortFoam Tobi	January 31, 2017 10:03 by Tobi	0	581
Unknown RASModel type mySpalartAllmaras (airfoil) Salim	January 31, 2017 04:34 by Salim	9	670
how to add turbulence model in OpenFoam Salim	January 30, 2017 21:26 by Salim	7	1,450
Boundary at phase interface - Inlet at a single point mehdiataei	January 30, 2017 06:36 by mehdiataei	0	309
Parallel processing sam.dj	January 29, 2017 02:52 by sam.dj	2	401
Polyurethane foaming simulations samiam1000	January 28, 2017 18:27 by mehdiataei	1	1,726
Writing OpenFoam header to the sampled output data to use as inlet b.c Eman.	January 27, 2017 06:08 by CliftonReed	3	652
Heat Flux as Boundary Condition NightWing	January 26, 2017 15:58 by nikitin-pro	2	1,610
Understanding BCs/transported quantities me3840	January 26, 2017 05:14 by C-L	1	399
rotorDiskSource using targetCoeffTrim jackkra	January 23, 2017 10:47 by jackkra	1	707
if function and turbulence->k() Zack	January 23, 2017 05:51 by floquation	11	1,023
FSI motion error thegauravonline	January 23, 2017 03:46 by thegauravonline	2	433
mesh quality problem for displacementSBRStress motion solver zhaozhenkai	January 22, 2017 12:02 by zhaozhenkai	0	648
How To Use OpenFOAM to model a jet engine? HRobertHS	January 22, 2017 01:14 by HRobertHS	0	763
How to export data on planes to CSV Files New-to-CFD	January 19, 2017 04:07 by akidess	1	1,726
Bulk Viscosity Tobi	January 18, 2017 17:36 by Tobi	0	882
Density and pressure in sonicFoam Endel	January 18, 2017 12:46 by Endel	0	452
simpleFoam with non uniform initial condition fails d.gavrila	January 18, 2017 12:07 by d.gavrila	0	490
Adjoint Optimization with RBF Morpher - Lift of 2D Airfoil hxaxtma	January 18, 2017 09:11 by verboomj	1	591
Slurry Erosive Wear karshtharyani	January 17, 2017 06:58 by mohitmak12	1	848
turbulentTemperatureRadCoupledMixedFvPatch JoeFriend	January 17, 2017 03:43 by chriss85	1	401
Using gmshToFoam RishabhG	January 16, 2017 08:55 by Jack80	1	858
Did you export *.dat data to excel? bye bye my blue	January 16, 2017 08:47 by Jack80	1	813
crack propagation example Hichem1990	January 15, 2017 19:03 by Hichem1990	0	608
laminar flow in one zone and kEpsilon model in the other zone. super1	January 15, 2017 11:44 by hxaxtma	3	677
calculating Force, Drag AND Lift coefficient bye bye my blue	January 15, 2017 00:38 by bye bye my blue	0	485
external aero simulation of the DrivAer car model florian_krause	January 14, 2017 12:35 by Vignesh2508	1	2,169
Launching OpenFOAM with MATLAB giovannibonino	January 13, 2017 21:48 by giovannibonino	0	640
OpenFOAM Boundary Conditions RishabhG	January 13, 2017 08:53 by Tobi	3	779

Read this first: How to ask a question on the forums

Page 51 of 214

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 18:47.