OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	August 14, 2022 13:55 by mikethe1wheelnut	25	50,603
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	March 25, 2023 07:50 by ancolli	19	59,147
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 07:34 by wyldckat	178	67,384
Sticky: How to give enough info to get help linnemann	September 20, 2017 09:19 by linnemann	8	55,206
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	September 2, 2021 05:29 by hakosaj	10	21,723
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 15:54 by rdbisme	17	20,472
problem with constant wall heat flux openfoam1	January 13, 2019 08:18 by calf.Z	6	7,189
runTime deji	January 17, 2019 09:14 by HoneyBadger	2	2,075
namespace Foam Argen	February 5, 2019 08:55 by Bruno_Jorge	4	4,023
Grabbing value of a dimensioned quantity / Problem creating a dimensioned tensor ThomasV	February 18, 2019 11:05 by deepbandivadekar	5	2,488
Dimension Error in OpenFOAM hakolekar	January 19, 2019 14:48 by shanvach	3	3,291
OpenFoam mapped boundary condition Eman.	January 19, 2019 06:10 by mAlletto	5	3,892
Getting started with CyclicAMI Algebraist	February 11, 2019 01:39 by Jikst	4	2,768
NASA rotor 37 ( 1 2) tom.opt	January 18, 2019 02:34 by ersoflow	20	4,467
OpenFOAM from CFD Direct cfdhelp	January 21, 2019 03:18 by HenrikJohansson	2	867
cellZone not taking all the cells inside rahulksoni	January 16, 2019 01:16 by rahulksoni	0	1,005
need an interphase mass transfer model for single component highend	January 15, 2019 09:21 by highend	2	927
Foam crashes due to bug or dodgy mesh, or something else? unsteady-eddie	January 19, 2019 12:56 by benchwell	3	752
Flow through a cylinder gone wrong heitorvitorc	February 19, 2019 14:30 by clapointe	1	886
blockMeshDict of airfoil in circular rotor sanket1527	January 13, 2019 08:23 by sanket1527	0	664
OpenFOAM - Passive Scalar Transported across Two Miscible Phases foamF	January 13, 2019 10:22 by foamF	0	775
Running a simple hydropower flow simulation with the use of an actuator disk EJohn	January 19, 2019 14:23 by EJohn	2	706
Heat generation at the mixing plane interface EnricoDeFilippi	January 17, 2019 14:37 by EnricoDeFilippi	0	835
Problems on "purgeWrite" and "writeCompression" for probe eddykendo	January 17, 2019 22:43 by eddykendo	0	1,566
Viscosity and pressure - Newtonian yambanshee	January 18, 2019 06:16 by HenrikJohansson	1	921
Problem with patchAverage Mcesar	January 25, 2019 06:39 by Mcesar	5	1,086
getting wrong forces and force coefficients in openfoam maddy11	January 23, 2019 01:09 by maddy11	2	1,902
Fresh_air and waste_air circulation with rhoReactingBuoyantFoam solver in a room Anupam	January 22, 2019 08:27 by Anupam	0	594
Water level doesn't rise in CFD-DEM simulation of air-water-solid. What should I chec gsiitd	January 23, 2019 00:25 by gsiitd	0	555
K-Omega SST wall treatment yambanshee	January 23, 2019 07:57 by tjuAeron	1	932
OpenFoam change library syntex	January 23, 2019 16:38 by syntex	0	735
Inlet and outlet on the same patch in openfoam? dela	February 2, 2019 09:08 by gkarlsen	5	1,575
forces and force coefficient maddy11	January 25, 2019 01:34 by yambanshee	1	845
Calculating y+ values in the inner cells raptorishungry	January 25, 2019 04:12 by tilasoldo	1	706
What is time in the SimpleFoam Solver? bshambaugh	January 27, 2019 13:48 by bshambaugh	1	1,930
2D airfoil Calculation is diverging losiola	January 31, 2019 01:29 by yambanshee	1	740
OpenFOAM v.6 pimpleFoam ignores resdiualControl Bazinga	January 28, 2019 06:33 by Bazinga	0	703
Spatially varying wall temperature daily	February 6, 2019 08:06 by gkarlsen	2	909
error is shown while solving problem using icoFoam solver pawansharma	February 6, 2019 04:25 by RobertHB	1	612
Checkerboarding > SimpleFoam yambanshee	February 6, 2019 05:12 by yambanshee	2	872
differences between 1812 and V6 pici	February 7, 2019 12:00 by Daniel_Khazaei	3	1,285
Suction Effect detox91	February 14, 2019 18:32 by detox91	0	686
Does extrude and createPatch utilities degrade mesh quality? Sashihara	February 11, 2019 16:08 by Sashihara	4	973
simflow with EDC model gotosky	February 16, 2019 08:20 by gotosky	0	685
overset mesh - collision of mesh maxonline	February 19, 2019 16:56 by Santiago	1	1,077
DES Model Regions in MPPICFoam saiguruprasad	February 19, 2019 23:31 by saiguruprasad	0	832

Read this first: How to ask a question on the forums

Page 187 of 239

187

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 09:52.